MK30DN512ZVLQ10R Freescale Semiconductor, MK30DN512ZVLQ10R Datasheet - Page 29

• Manufacturer Part Number: MK30DN512ZVLQ10R
• Description: ARM Microcontrollers - MCU KINETIS 512K LCD
• Manufacturer: Freescale Semiconductor

Specifications of MK30DN512ZVLQ10R

• Rohs: yes
• Core: ARM Cortex M4
• Processor Series: K30
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 128 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 1.71 V to 3.6 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: LQFP-144
• Mounting Style: SMD/SMT

1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
2. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0.
3. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency deviation
4. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1.
5. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
6. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
7. Excludes any oscillator currents that are also consuming power while PLL is in operation.
8. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of
9. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled
6.3.2 Oscillator electrical specifications
This section provides the electrical characteristics of the module.
6.3.2.1 Oscillator DC electrical specifications
Freescale Semiconductor, Inc.
Symbol
I
I
DDOSC
DDOSC
mode).
(Δf
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
each PCB and results will vary.
(BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes
it is already running.
V
C
C
DD
dco_t
x
y
) over voltage and temperature should be considered.
Supply voltage
Supply current — low-power mode (HGO=0)
Supply current — high gain mode (HGO=1)
EXTAL load capacitance
XTAL load capacitance
Description
• 32 kHz
• 4 MHz
• 8 MHz (RANGE=01)
• 16 MHz
• 24 MHz
• 32 MHz
• 32 kHz
• 4 MHz
• 8 MHz (RANGE=01)
• 16 MHz
• 24 MHz
• 32 MHz
Table 16. Oscillator DC electrical specifications
K30 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Table continues on the next page...
1.71
Min.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Peripheral operating requirements and behaviors
Typ.
500
200
300
950
400
500
1.2
1.5
2.5
25
—
—
—
3
4
Max.
3.6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unit
mA
mA
mA
mA
mA
μA
μA
μA
μA
μA
μA
nA
V
Notes
2,
2,
1
1
3
3
29