1893AFILFT IDT, 1893AFILFT Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
1893AFILFT
Manufacturer Part Number
1893AFILFT
Description
Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
Manufacturer
IDT
Datasheet
1.1893AFLF.pdf
(136 pages)
Specifications of 1893AFILFT
Rohs
yes
Part # Aliases
ICS1893AFILFT
- Current page: 21 of 136
- Download datasheet (963Kb)
5.1.2.3 Software Reset
5.2 Power-Down Operations
ICS1893AF, Rev. D 10/26/04
Entering Software Reset
Initiation of a software reset occurs when a management entity writes a logic one to Control Register bit
0.15. When this write occurs, the ICS1893AF enters the reset state for two REF_IN clock cycles.
Note:
Exiting Software Reset
At the completion of a reset (either hardware, power-on, or software), the ICS1893AF sets all registers to
their default values. This action automatically clears (that is, sets equal to logic zero) Control Register bit
0.15, the software reset bit. Therefore, for a software reset (only), bit 0.15 is a self-clearing bit that indicates
the completion of the reset process.
Note:
1. The RESETn pin is active low but Control Register bit 0.15 is active high.
2. Exiting a software reset is nearly identical to exiting a hardware reset or a power-on reset, except that
3. The Control Register bit 0.15 does not represent the status of a hardware reset. It is a self-clearing bit
The ICS1893AF enters the power-down state whenever either (1) the RESETn pin is low or (2) Control
Register bit 0.11 (the Power-Down bit) is logic one. In the power-down state, the ICS1893AF disables all
internal functions and drives all MAC/Repeater Interface output pins to logic zero except for those that
support the MII Serial Management Port. In addition, the ICS1893AF tri-states its Twisted-Pair Transmit
pins (TP_TXP and TP_TXN) to achieve an additional reduction in power.
There is one significant difference between entering the power-down state by setting Control Register bit
0.11 as opposed to entering the power-down state during a reset. When the ICS1893AF enters the
power-down state:
•
•
For more information on power-down operations, see the following:
•
•
By setting Control Register bit 0.11, the ICS1893AF maintains the value of all Management Register bits
except for the latching low (LL), latching high (LH), and latching maximum (LMX) status bits. Instead,
these LL, LH, and LMX Management Register bits are re-initialized to their default values.
During a reset, the ICS1893AF sets all of its Management Register bits to their default values. It does not
maintain the state of any Management Register bit.
Section 8.14, “Register 19: Extended Control Register 2”
Section 10.4, “DC Operating
consumption while in the power-down state
ICS1893AF Data Sheet - Release
upon exiting a software-initiated reset, the ICS1893AF does not re-latch its Serial Management Port
Address into the Extended Control Register. [For information on the Serial Management Port Address,
see
that is used to initiate a software reset. During a hardware or power-on reset, Control Register bit 0.15
does not get set to logic one. As a result, this bit 0.15 cannot be used to indicate the completion of the
reset process for hardware or power-on resets.
Entering a software reset is nearly identical to entering a hardware reset or a power-on reset,
except that during a software-initiated reset, the ICS1893AF does not enter the power-down state.
Section 8.11.3, “PHY Address (bits
Copyright © 2004, Integrated Circuit Systems, Inc.
Characteristics”, which has tables that specify the ICS1893AF power
16.10:6)”.]
All rights reserved.
21
Chapter 5 Operating Modes Overview
October, 2004
Related parts for 1893AFILFT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICS1893AFI](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_tmb.jpg)
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
![ICS1893AF](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_tmb.jpg)
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
![1893](/images/no-image3.png)
Part Number:
Description:
#1893 LAMP T-3 1/4 14V 330MA MINIATURE BAYONET BASE
Manufacturer:
EIKO
![1893-10PK](/photos/22/65/226522/4436756_tmb.jpg)
Part Number:
Description:
LAMP, INCANDESCENT, BAYONET, 14V
Manufacturer:
CHICAGO MINIATURE LIGHTING, LLC
Datasheet:
![IDT TEMP SENSOR SAMPLE KIT](/images/manufacturer_photos/0/3/333/integrated_device_technology__idt__tmb.jpg)
Part Number:
Description:
IDT TS3000AND TSE2002 SENSORS SAMPLE PACK OFFER
Manufacturer:
Integrated Device Technology (Idt)
![IDT-00/E](/photos/21/57/215774/4550311_tmb.jpg)
Part Number:
Description:
THERMOCOUPLE DIGITAL PANEL METER
Manufacturer:
NEWPORT ELECTRONICS
![IDT%4841CP](/images/manufacturer_photos/0/3/334/integrated_device_technology__inc__tmb.jpg)
Part Number:
Description:
High-performance CMOS bus interface latches
Manufacturer:
Integrated Device Technology, Inc.
![IDT-3030](/images/no-image3.png)
Part Number:
Description:
Accessories Connectors and Cables
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
![IDT-5101](/images/no-image3.png)
Part Number:
Description:
Accessories 5.25 Industrial Disk Tray
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
![IDT74FCT162244ATPA](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_tmb.jpg)
Part Number:
Description:
IDT PART
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet: