1893AFILFT IDT, 1893AFILFT Datasheet - Page 41
1893AFILFT
Manufacturer Part Number
1893AFILFT
Description
Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
Manufacturer
IDT
Datasheet
1.1893AFLF.pdf
(136 pages)
Specifications of 1893AFILFT
Rohs
yes
Part # Aliases
ICS1893AFILFT
- Current page: 41 of 136
- Download datasheet (963Kb)
7.3.3 PCS/PMA Transmit Modules
7.3.3.1 PCS Transmit Module
7.3.3.2 PMA Transmit Module
ICS1893AF, Rev. D 10/26/04
Both the PCS and PMA sublayers have Transmit modules.
The ICS1893AF PCS Transmit module accepts nibbles from the MAC/Repeater Interface and converts the
nibbles into 5-bit ‘code groups’ (referred to here as ‘symbols’). In addition, the PCS Transmit module
performs a parallel-to-serial conversion on the symbols, and subsequently passes the resulting serial bit
stream to the PMA sublayer.
The first 16 nibbles of each MAC/Repeater Frame represent the Frame Preamble. The PCS replaces the
first two nibbles of the Frame Preamble with the Start-of-Stream Delimiter (SSD), that is, the symbols /J/K/.
After receipt of the last Frame nibble, detected when TX_EN = FALSE, the PCS appends to the end of the
Frame an End-of-Stream Delimiter (ESD), that is, the symbols /T/R/. (The ICS1893AF PCS does not alter
any other data included within the Frame.)
The PCS Transmit module also performs collision detection. In compliance with the ISO/IEC specification,
when the transmission and reception of data occur simultaneously and the ICS1893AF is in:
•
•
The ICS1893AF PMA Transmit module accepts a serial bit stream from its PCS and converts the data into
NRZI format. Subsequently, the PMA passes the NRZI bit stream to the Twisted-Pair Physical Medium
Dependent (TP-PMD) sublayer.
The ICS1893AF PMA Transmit module uses a digital PLL to synthesize a transmit clock from the Clock
Reference Interface. When the ICS1893AF is configured for an interface that is:
•
•
•
Note:
1. All of the TXCLK signals are derived from the REF_IN signal that goes to the digital PLL.
2. For the MII, for both the 10Base-T and 100Base-TX modes, the clock that is generated synchronizes
Half-duplex mode, the ICS1893AF asserts the collision detection signal (COL).
Full-duplex mode, COL is always FALSE.
10M MII (that is, 10Base-T), the TXCLK signal is 2.5 MHz
10M Serial Interface, the TXCLK signal is 10 MHz
Either of the following, the TXCLK signal (a buffered version of the REF_IN signal) is 25 MHz:
– 100M MII (that is, 100Base-TX)
– 100M Symbol Interface
ICS1893AF Data Sheet - Release
all data transfers across the MII.
Copyright © 2004, Integrated Circuit Systems, Inc.
All rights reserved.
41
Chapter 7 Functional Blocks
October, 2004
Related parts for 1893AFILFT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
#1893 LAMP T-3 1/4 14V 330MA MINIATURE BAYONET BASE
Manufacturer:
EIKO
Part Number:
Description:
LAMP, INCANDESCENT, BAYONET, 14V
Manufacturer:
CHICAGO MINIATURE LIGHTING, LLC
Datasheet:
Part Number:
Description:
IDT TS3000AND TSE2002 SENSORS SAMPLE PACK OFFER
Manufacturer:
Integrated Device Technology (Idt)
Part Number:
Description:
THERMOCOUPLE DIGITAL PANEL METER
Manufacturer:
NEWPORT ELECTRONICS
Part Number:
Description:
High-performance CMOS bus interface latches
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Accessories Connectors and Cables
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Accessories 5.25 Industrial Disk Tray
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
IDT PART
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet: