MAX9260GCB/V+TGG4 Maxim Integrated, MAX9260GCB/V+TGG4 Datasheet - Page 13

• Manufacturer Part Number: MAX9260GCB/V+TGG4
• Description: Serializers & Deserializers - Serdes Multimedia Serial Link
• Manufacturer: Maxim Integrated
• Type: Deserializerr

Specifications of MAX9260GCB/V+TGG4

• Rohs: yes
• Data Rate: 2.5 Gbit/s
• Input Type: CML
• Output Type: CMOS/LVCMOS
• Number Of Inputs: 1
• Number Of Outputs: 30
• Operating Supply Voltage: 1.7 V to 3.6 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: TQFP-64 EP
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT

Table1.InductorSizeComparison
The inductor value must be chosen so that the maximum
inductor current does not reach the device’s minimum
current limit. The optimum operating point is usually
found between 25% and 35% ripple current. When pulse
skipping (FSYNC low and light loads), the inductor value
also determines the load-current value at which PFM/
PWM switchover occurs.
Find a low-loss inductor having the lowest possible
DC resistance that fits in the allotted dimensions. Most
inductor manufacturers provide inductors in standard
values, such as 1.0FH, 1.5FH, 2.2FH, 3.3FH, etc. Also
look for nonstandard values, which can provide a bet-
ter compromise in LIR across the input voltage range. If
using a swinging inductor (where the no-load inductance
decreases linearly with increasing current), evaluate
the LIR with properly scaled inductance values. For
the selected inductance value, the actual peak-to-peak
inductor ripple current (DI
where DI
Ferrite cores are often the best choices, although pow-
dered iron is inexpensive and can work well at 200kHz.
The core must be large enough not to saturate at the
peak inductor current (I
The input filter capacitor reduces peak currents drawn
from the power source and reduces noise and voltage
ripple on the input caused by the circuit’s switching.
The input capacitor RMS current requirement (I
defined by the following equation:
Faster load response
Smaller form factor
I
RMS
INDUCTOR
Lower price
SMALLER
∆
I
PEAK
I
INDUCTOR
=
I
LOAD(MAX)
=
 � ��������������������������������������������������������������� Maxim Integrated Products  13
I
LOAD(MAX)
is in A, L is in H, and f
INDUCTORSIZE
=
PEAK
V
INDUCTOR
OUT
V
V
):
OUT
SUP
(V
+
Larger fixed-frequency
∆
SUP
(V
range in skip mode
×
I
V
Higher efficiency
INDUCTOR
f
SUP
) is defined by:
SUP
Smaller ripple
SW
Input Capacitor
−
LARGER
2
36V, 2.2MHz Step-Down Converter
V
×
−
OUT
L
SW
V
OUT
)
is in Hz.
)
RMS
) is
with Low Operating Current
I
equals twice the output voltage (V
I
Choose an input capacitor that exhibits less than +10NC
self-heating temperature rise at the RMS input current for
optimal long-term reliability.
The input-voltage ripple is composed of DV
by the capacitor discharge) and DV
equivalent series resistance (ESR) of the capacitor). Use
low-ESR ceramic capacitors with high ripple-current
capability at the input. Assume the contribution from the
ESR and capacitor discharge equal to 50%. Calculate
the input capacitance and ESR required for a specified
input-voltage ripple using the following equations:
where
and
where I
duty cycle.
The output filter capacitor must have low enough ESR to
meet output ripple and load-transient requirements, yet
have high enough ESR to satisfy stability requirements.
The output capacitance must be high enough to absorb
the inductor energy while transitioning from full-load
to no-load conditions without tripping the overvoltage
fault protection. When using high-capacitance, low-ESR
capacitors, the filter capacitor’s ESR dominates the
output-voltage ripple. So the size of the output capaci-
tor depends on the maximum ESR required to meet the
output-voltage ripple (V
The actual capacitance value required relates to the
physical size needed to achieve low ESR, as well as
to the chemistry of the capacitor technology. Thus, the
capacitor is usually selected by ESR and voltage rating
rather than by capacitance value.
RMS
RMS(MAX)
has a maximum value when the input voltage
OUT
C
V
RIPPLE(P-P)
IN
= I
is the maximum output current, and D is the
=
LOAD(MAX)
∆
I
OUT
I
L
∆
=
V
ESR
Q
(V
×
D(1 D)
×
= ESR × I
SUP
IN
f
RIPPLE(P-P)
SW
V
/2.
−
=
SUP
−
I
OUT
V
∆
OUT
×
and
V
LOAD(MAX)
f
ESR
MAX16907
SW
+
) V
∆
) specifications:
×
D
2
I
×
L
ESR
SUP
L
=
OUT
Output Capacitor
V
V
SUPSW
(caused by the
OUT
= 2V
× LIR
Q
OUT
(caused
), so