SSL1523AP/N2,112 NXP Semiconductors, SSL1523AP/N2,112 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
SSL1523AP/N2,112
Specifications of SSL1523AP/N2,112
Related parts for SSL1523AP/N2,112
SSL1523AP/N2,112 Summary of contents
Page 1
SSL1523A SMPS ICs for mains LED drivers Rev. 1 — 25 April 2012 1. General description The SSL1523A is a Switched Mode Power Supply (SMPS) controller IC that operate directly from the rectified universal AC mains implemented in ...
Page 2
... NXP Semiconductors 3. Applications Retro-fit LED lamps LED ballasts Contour lighting Channel letter lighting Commercial lighting, such as cabinet or freezer lights Other lighting applications 4. Quick reference data Table 1. Quick reference data Symbol Parameter V voltage on pin DRAIN DRAIN ...
Page 3
... NXP Semiconductors 6. Block diagram SSL1523AP 2 GND stop 3 OSCILLATOR RC low freq REG Fig 1. Block diagram 7. Pinning information 7.1 Pinning Fig 2. SSL1523A Product data sheet SUPPLY LOGIC THERMAL SHUTDOWN PROTECTION LOGIC POWER - UP RESET overcurrent GND 2 SSL1523AP 3 RC REG 4 Pinning diagram (DIP8) All information provided in this document is subject to legal disclaimers. Rev. 1 — ...
Page 4
... NXP Semiconductors 7.2 Pin description Table 3. Symbol V CC GND RC REG AUX SOURCE n.c. DRAIN 8. Functional description The SSL1523A is the heart of a compact flyback converter, with the IC placed at the primary side. The auxiliary winding of the transformer can be used for indirect feedback to control the isolated output. This additional winding also powers the IC. A more accurate control of the output voltage and/or current can be implemented with an additional secondary sensing circuit and optocoupler feedback ...
Page 5
... NXP Semiconductors at low duty factors is easily realized. For high efficiency, the frequency is reduced as soon as the duty factor drops below its low power threshold. This is accomplished by increasing the oscillator charge time. To ensure that the capacitor can be charged within the charge time, the value of the oscillator capacitor should be limited to approximately 1 nF ...
Page 6
... NXP Semiconductors Fig 3. Figure 4 the output voltage V the factor N (determined by the turns ratio of the transformer). system switches at the minimum drain voltage for ringing frequencies of 480 kHz, thus reducing the switch-on losses to a minimum. At 200 kHz, the next primary stroke is started at 33 ° before the valley. The switch-on losses are still reduced significantly. ...
Page 7
... NXP Semiconductors 8.5 Demagnetization The system operates in discontinuous conduction mode all the time. As long as the secondary stroke has not ended, the oscillator will not start a new primary stroke. During the first t suppression may be necessary in applications where the transformer has a large leakage inductance and at low output voltages. ...
Page 8
... NXP Semiconductors 8.10.4 Ripple A minimum ripple is obtained in a system designed for a maximum duty factor under normal operating conditions and a minimized dead time. The magnitude of the ripple in the output voltage is determined by the frequency and duty factor of the converter, the output current level, and the value and the output capacitor ...
Page 9
... NXP Semiconductors 9. Limiting values Table 4. In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are measured with respect to ground; positive currents flow into the device; pins V current driven and pins REG and AUX are not allowed to be voltage driven. ...
Page 10
... NXP Semiconductors 11. Characteristics Table 6. Characteristics Measurement data valid amb positive when flowing into the IC; unless otherwise specified. Symbol Parameter Supply I operating supply current CC(oper) I start-up supply current CC(startup) I supply current CC V start-up supply voltage CC(startup) V stop supply voltage CC(stop) I current on pin DRAIN ...
Page 11
... NXP Semiconductors Table 6. Characteristics …continued Measurement data valid amb positive when flowing into the IC; unless otherwise specified. Symbol Parameter drain-source on-state resistance R DSon t fall time on pin DRAIN f(DRAIN) Temperature protection T protection temperature prot T hysteresis of protection prot(hys) temperature SSL1523A Product data sheet ° ...
Page 12
... NXP Semiconductors 12. Application information mains R1 Fig 5. Typical configuration of SSL1523A - primary sensing SSL1523A Product data sheet LF CF1 CF2 VCC SSL1523AP All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 April 2012 SSL1523A SMPS ICs for mains LED drivers ...
Page 13
... NXP Semiconductors 13. Package outline DIP8: plastic dual in-line package; 8 leads (300 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions UNIT max. min. max. mm 4.2 0.51 3.2 inches 0.17 0.02 0.13 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. ...
Page 14
... NXP Semiconductors 14. Abbreviations Table 7. Acronym BiCMOS DMOS ESR EZ-HV SOI FET SMPS SOPS 15. Revision history Table 8. Revision history Document ID Release date SSL1523A v.1 20120425 SSL1523A Product data sheet Abbreviations Description Bipolar Complementary Metal Oxide Semiconductor Diffusion Metal Oxide Semiconductor Equivalent Series Resistance Easy High Voltage Silicon-On-Insulator ...
Page 15
... Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice ...
Page 16
... NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ ...
Page 17
... NXP Semiconductors 18. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 5 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 Functional description . . . . . . . . . . . . . . . . . . . 4 8.1 Start-up and undervoltage lockout . . . . . . . . . . 4 8.2 Oscillator 8.3 Duty factor control . . . . . . . . . . . . . . . . . . . . . . 5 8.4 Valley switching . . . . . . . . . . . . . . . . . . . . . . . . 5 8.5 Demagnetization ...