MT46V16M16P-6T L:F TR Micron Technology Inc, MT46V16M16P-6T L:F TR Datasheet - Page 39
![IC DDR SDRAM 256MBIT 6NS 66TSOP](/photos/7/22/72288/mfg557-66-tsop_sml.jpg)
MT46V16M16P-6T L:F TR
Manufacturer Part Number
MT46V16M16P-6T L:F TR
Description
IC DDR SDRAM 256MBIT 6NS 66TSOP
Manufacturer
Micron Technology Inc
Datasheet
1.MT46V16M16CY-5BK_TR.pdf
(93 pages)
Specifications of MT46V16M16P-6T L:F TR
Format - Memory
RAM
Memory Type
DDR SDRAM
Memory Size
256M (16Mx16)
Speed
6ns
Interface
Parallel
Voltage - Supply
2.3 V ~ 2.7 V
Operating Temperature
0°C ~ 70°C
Package / Case
66-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Figure 12:
PDF: 09005aef80768abb/Source: 09005aef82a95a3a
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. O, Core DDR: Rev. B 1/09 EN
Derating Data Valid Window (
30. The input capacitance per pin group will not differ by more than this maximum
31. CK and CK# input slew rate must be ≥1 V/ns (≥2 V/ns if measured differentially).
32. DQ and DM input slew rates must not deviate from DQS by more than 10%. If the DQ/
33. V
34. The clock is allowed up to ±150ps of jitter. Each timing parameter is allowed to vary by
35.
36. READs and WRITEs with auto precharge are not allowed to be issued until
37. Any positive glitch must be less than 1/3 of the clock cycle and not more than +400mV
38. Normal output drive curves:
38b. The driver pull-down current variation, within nominal voltage and temperature
38a. The full driver pull-down current variation from MIN to MAX process; tempera-
amount for any given device.
DM/DQS slew rate is less than 0.5 V/ns, timing must be derated: 50ps must be added
to
-6T speed grades, the slew rate must be ≥0.5 V/ns. If the slew rate exceeds 4 V/ns,
functionality is uncertain.
the same amount.
t
and CK# inputs, collectively, during bank active.
can be satisfied prior to the internal PRECHARGE command being issued.
or 2.9V (+300mV or 2.9V maximum for -5B), whichever is less. Any negative glitch
must be less than 1/3 of the clock cycle and not exceed either
-5B), whichever is more positive. The average cannot be below the +2.5V (2.6V for -5B)
minimum.
3.0ns
2.5ns
2.0ns
1.5ns
1.0ns
HP (MIN) is the lesser of
DD
t
DS and
ture and voltage will lie within the outer bounding lines of the V-I curve of
Figure 13 on page 38.
limits, is expected, but not guaranteed, to lie within the inner bounding lines of
the V-I curve of Figure 13 on page 38.
must not vary more than 4% if CKE is not active while any bank is active.
50/50
2.00
1.60
2.75
2.50
2.10
t
DH for each 100 mV/ns reduction in slew rate. For -5B, -6, and
1.97
1.58
2.71
2.46
2.07
t
QH –
49/51
1.94
1.55
2.68
2.43
2.04
t
t
DQSQ)
CL (MIN) and
37
1.91
1.53
2.64
2.39
2.01
Clock Duty Cycle
48/53
1.88
1.50
2.60
2.35
1.98
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Electrical Specifications – DC and AC
t
1.85
1.48
2.56
2.31
1.95
CH (MIN) actually applied to the device CK
256Mb: x4, x8, x16 DDR SDRAM
47/53
1.82
1.45
2.53
2.28
1.92
1.79
1.43
2.49
2.24
1.89
46/54
©2003 Micron Technology, Inc. All rights reserved.
1.76
1.40
2.45
2.20
1.86
–
300mV or 2.2V (2.4V for
-6T @ t CK = 7.5ns
-75E / -75 @ t CK = 7.5ns
-6 @ t CK = 6ns
-6T @ t CK = 6ns
-5B @ t CK = 5ns
1.73
1.38
2.41
2.16
1.83
45/55
2.13
1.70
1.35
2.38
1.80
t
RAS (MIN)