MT28F008B3VG-9 B TR Micron Technology Inc, MT28F008B3VG-9 B TR Datasheet - Page 12
![IC FLASH 8MBIT 90NS 40TSOP](/photos/7/30/73004/mfg557-40-tsop_sml.jpg)
MT28F008B3VG-9 B TR
Manufacturer Part Number
MT28F008B3VG-9 B TR
Description
IC FLASH 8MBIT 90NS 40TSOP
Manufacturer
Micron Technology Inc
Datasheet
1.MT28F008B3VG-9_B.pdf
(30 pages)
Specifications of MT28F008B3VG-9 B TR
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
8M (1M x 8)
Speed
90ns
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
40-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Command Execution
ferent operational modes. Each mode allows specific
operations to be performed. Several modes require a
sequence of commands to be written before they are
reached. The following section describes the proper-
ties of each mode, and Table 6 lists all command
sequences required to perform the desired operation.
Read Array
upon power-up and after a RESET. If the device is in
any other mode, READ ARRAY (FFh) must be given to
return to the array read mode. Unlike the WRITE
SETUP command (40h), READ ARRAY does not need
to be given before each individual READ access.
IDENTIFY DEVICE
to enter the identify device mode. While the device is
in this mode, any READ produces the device identifi-
cation when A0 is HIGH and the manufacturer com-
patibility identification when A0 is LOW. The device
remains in this mode until another command is given.
Write Sequence
the array. WRITE SETUP (40h or 10h) is given in the
first cycle. The next cycle is the WRITE, during which
Table 6:
NOTE:
09005aef81136a91
Q10.fm - Rev. E 6/04 EN
READ ARRAY
IDENTIFY DEVICE
READ STATUS REGISTER
CLEAR STATUS REGISTER
ERASE SETUP/CONFIRM
ERASE SUSPEND/RESUME
WRITE SETUP/WRITE
ALTERNATE WORD/BYTE WRITE
1. Must follow WRITE or ERASE CONFIRM commands to the CEL in order to enable Flash array READ cycles.
2. IA = Identify Address: 00h for manufacturer compatibility ID; 01h for device ID.
3. ID = Identify Data.
4. SRD = Status Register Data.
5. BA = Block Address (A12–A19).
6. Addresses are “Don’t Care” in first cycle but must be held stable.
7. WA = Address to be written; WD = Data to be written to WA.
Commands are issued to bring the device into dif-
The array read mode is the initial state of the device
IDENTIFY DEVICE (90h) may be written to the CEL
Two consecutive cycles are needed to input data to
COMMANDS
Command Sequences
CYCLES
REQ’D
BUS
1
3
2
1
2
2
2
2
OPERATION
ADDRESS
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
SMART 3 BOOT BLOCK FLASH MEMORY
12
CYCLE
FIRST
X
X
X
X
X
X
X
X
the write address and data are issued and V
brought to V
requires that the RP# pin be brought to V
pin be brought HIGH at the same time V
to V
V
(SR7 = 1).
bit (SR7) is at 0, and the device does not respond to any
commands. Any READ operation produces the status
register contents on DQ0–DQ7. When the ISM status
bit (SR7) is set to a logic 1, the WRITE has been com-
pleted, and the device goes into the status register read
mode until another command is given.
aborted except by a RESET or by powering down the
part. Doing either during a WRITE corrupts the data
being written. If only the WRITE SETUP command has
been given, the WRITE may be nullified by performing
a null WRITE. To execute a null WRITE, FFh must be
written when BYTE# is LOW, or FFFFh must be written
when BYTE# is HIGH. When the ISM status bit (SR7)
has been set, the device is in the status register read
mode until another command is issued.
PP
While the ISM executes the WRITE, the ISM status
After the ISM has initiated the WRITE, it cannot be
PPH
must be held at V
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DATA
. The ISM now begins to write the word or byte.
90h
70h
50h
20h
B0h
40h
10h
FFh
OPERATION
PPH
ADDRESS
WRITE
WRITE
WRITE
WRITE
READ
READ
. Writing to the boot block also
PPH
until the WRITE is completed
SECOND
CYCLE
©2001 Micron Technology, Inc. All rights reserved.
WA
WA
BA
IA
X
X
DATA
SRD
D0h
D0h
WD
WD
ID
HH
PP
or the WP#
is brought
8Mb
NOTES
2, 3
5, 6
6, 7
6, 7
1
4
PP
is