M24C08-WMN6 STMicroelectronics, M24C08-WMN6 Datasheet - Page 8
![IC EEPROM 8KBIT 400KHZ 8SOIC](/photos/1/38/13851/497-8-soic_sml.jpg)
M24C08-WMN6
Manufacturer Part Number
M24C08-WMN6
Description
IC EEPROM 8KBIT 400KHZ 8SOIC
Manufacturer
STMicroelectronics
Datasheet
1.M24C01-WMN6TP.pdf
(39 pages)
Specifications of M24C08-WMN6
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
8K (1K x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-1614-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M24C08-WMN6
Manufacturer:
ST
Quantity:
16 000
Part Number:
M24C08-WMN6
Manufacturer:
ST
Quantity:
20 000
Part Number:
M24C08-WMN6P
Manufacturer:
ST
Quantity:
20 000
Part Number:
M24C08-WMN6T
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M24C08-WMN6T/LBA
Manufacturer:
PULSE
Quantity:
5 985
Part Number:
M24C08-WMN6T/LBA
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M24C08-WMN6T/WBA
Manufacturer:
ST
Quantity:
2 500
Company:
Part Number:
M24C08-WMN6T/WBA
Manufacturer:
IR
Quantity:
2 500
Part Number:
M24C08-WMN6TP
Manufacturer:
STM
Quantity:
20 000
Signal description
2
2.1
2.2
2.3
2.3.1
8/39
Signal description
Serial Clock (SCL)
This input signal is used to strobe all data in and out of the device. In applications where this
signal is used by slave devices to synchronize the bus to a slower clock, the bus master
must have an open drain output, and a pull-up resistor can be connected from Serial Clock
(SCL) to V
most applications, though, this method of synchronization is not employed, and so the pull-
up resistor is not necessary, provided that the bus master has a push-pull (rather than open
drain) output.
Serial Data (SDA)
This bidirectional signal is used to transfer data in or out of the device. It is an open drain
output that may be wire-ORed with other open drain or open collector signals on the bus. A
pull up resistor must be connected from Serial Data (SDA) to V
the value of the pull-up resistor can be calculated).
Chip Enable (E0, E1, E2)
These input signals are used to set the value that is to be looked for on the three least
significant bits (b3, b2, b1) of the 7-bit device select code. These inputs must be tied to V
or V
floating), E0, E1, E2 are read as low (0,0,0).
Figure 4.
Write Control (WC)
This input signal is useful for protecting the entire contents of the memory from inadvertent
write operations. Write operations are disabled to the entire memory array when Write
Control (WC) is driven High. When unconnected, the signal is internally read as V
Write operations are allowed.
When Write Control (WC) is driven High, device select and address bytes are
acknowledged, data bytes are not acknowledged.
SS
, to establish the device select code as shown in
CC
Device select code
.
(Figure 5
indicates how the value of the pull-up resistor can be calculated). In
Doc ID 5067 Rev 16
E i
M24Cxx
V CC
V SS
M24C16, M24C08, M24C04, M24C02, M24C01
E i
M24Cxx
V CC
V SS
Ai11650
Figure
4. When not connected (left
CC
.
(Figure 5
indicates how
IL
, and
CC