ADE7769AR Analog Devices Inc, ADE7769AR Datasheet - Page 11

• Manufacturer Part Number: ADE7769AR
• Description: IC ENERGY METER POS W/OSC 16SOIC
• Manufacturer: Analog Devices Inc

Specifications of ADE7769AR

• Input Impedance: 320 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 5mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Meter Type: Single Phase
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

where:
i(t) is the instantaneous current.
I
I
Using Equations 2 and 3, the real power (P) can be expressed in
terms of its fundamental real power (P
power (P
where:
and
In Equation 5, a harmonic real power component is generated
for every harmonic, provided that harmonic is present in both
the voltage and current waveforms. The power factor calcu-
lation has previously been shown to be accurate in the case of a
pure sinusoid. Therefore, the harmonic real power must also
correctly account for the power factor because it is made up of
a series of pure sinusoids.
Note that the input bandwidth of the analog inputs is 7 kHz at
the nominal internal oscillator frequency of 450 kHz.
ANALOG INPUTS
Channel V1 (Current Channel)
The voltage output from the current sensor is connected to the
ADE7769 here. Channel V1 is a fully differential voltage input.
V1P is the positive input with respect to V1N.
The maximum peak differential signal on Channel V1 should
be less than ±30 mV (21 mV rms for a pure sinusoidal signal)
for specified operation.
β
0
h
is the dc component.
is the rms value of current harmonic h.
h
φ
P
is the phase angle of the current harmonic.
1
1
t i
φ
P
+30mV
–30mV
=
=
) (
h
H
V
V
α
=
CM
=
=
1
H
1
α
) as P = P
×
I
−
h
∑
V1
∞
h
O
≠
I
1
Figure 17. Maximum Signal Levels, Channel V1
β
V
−
1
+
1
h
cos
β
×
h
2
I
φ
×
h
1
1
+ P
h
∑
cos
∞
DIFFERENTIAL INPUT
≠
o
I
H
±30mV MAX PEAK
h
φ
COMMON-MODE
×
h
sin
±6.25mV MAX
(
hω
t
+
β
AGND
1
h
) and harmonic real
)
V1
V
CM
V1P
V1N
Rev. A | Page 11 of 20
(3)
(4)
(5)
Figure 17 shows the maximum signal levels on V1P and V1N.
The maximum differential voltage is ±30 mV. The differential
voltage signal on the inputs must be referenced to a common
mode, for example, AGND. The maximum common-mode
signal is ±6.25 mV, as shown in Figure 17.
Channel V2 (Voltage Channel)
The output of the line voltage sensor is connected to the
ADE7769 at this analog input. Channel V2 is a fully differential
voltage input with a maximum peak differential signal of
±165 mV. Figure 18 shows the maximum signal levels that can
be connected to the ADE7769 Channel V2.
Channel V2 is usually driven from a common-mode voltage,
that is, the differential voltage signal on the input is referenced
to a common mode (usually AGND). The analog inputs of the
ADE7769 can be driven with common-mode voltages of up to
25 mV with respect to AGND. However, best results are
achieved using a common mode equal to AGND.
Typical Connection Diagrams
Figure 19 shows a typical connection diagram for Channel V1.
A shunt is the current sensor selected for this example because
of its low cost compared to other current sensors, such as the
current transformer (CT). This IC is ideal for low current meters.
Figure 20 shows a typical connection for Channel V2. Typically,
the ADE7769 is biased around the phase wire, and a resistor
divider is used to provide a voltage signal that is proportional to
the line voltage. Adjusting the ratio of R
convenient way of carrying out a gain calibration on a meter.
+165mV
–165mV
V
CM
V2
PHASE
Figure 18. Maximum Signal Levels, Channel V2
Figure 19. Typical Connection for Channel V1
SHUNT
AGND
NEUTRAL
DIFFERENTIAL INPUT
±165mV MAX PEAK
COMMON-MODE
R
R
±30mV
F
F
±25mV MAX
C
C
F
F
AGND
V1N
A
V1P
, R
V2
V
B
CM
, and R
B
V2P
V2N
ADE7769
F
is also a