MAX3740AETG+T Maxim Integrated Products, MAX3740AETG+T Datasheet - Page 4

• Manufacturer Part Number: MAX3740AETG+T
• Description: IC DRIVER SFP VCSEL 24-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Laser Diode Driverr

Specifications of MAX3740AETG+T

• Data Rate: 3.2Gbps
• Number Of Channels: 1
• Voltage - Supply: 2.97 V ~ 3.63 V
• Current - Supply: 55mA
• Current - Modulation: 15mA
• Current - Bias: 15mA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-TQFN Exposed Pad
• Mounting Type: Surface Mount
• Supply Voltage (max): 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Supply Current: 55 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.2Gbps SFP VCSEL Driver with Diagnostic
Monitors
ELECTRICAL CHARACTERISTICS (continued)
(V
+25°C, unless otherwise noted.)
4
Note 1: Supply current measurements exclude I
Note 2: Tested with R
Note 3: Measured by applying a pattern that contains 20µs of K28.5, followed by 5µs of zeros, then 20µs of K28.5, followed by 5µs
Note 4: V
Note 5: Variation of bias monitor gain for any single part over the range of V
Note 6: Guaranteed by design and characterization.
Note 7: Measured electrically with a 50Ω load AC-coupled to OUT+.
Note 8: Deterministic jitter is the peak-to-peak deviation from the ideal time crossings measured with a K28.5 bit pattern at 3.2Gbps
SAFETY FEATURES (see the Typical Operating Characteristics section)
High-Current Fault Threshold
V
Power-Monitor Fault Threshold
TX Disable Time
TX Disable Negate Time
Fault Reset Time
Power-On Time
Fault Assert Time
Fault Delay Time
TX_DISABLE Reset
CC
BIAS
_______________________________________________________________________________________
= +2.97V to +3.63V, T
Fault Threshold
of ones. Data rate is equal to 2.5Gbps, with inputs filtered using 1.8GHz Bessel filters.
(00111110101100000101).
BIAS
PARAMETER
< V
CC
- 0.7V.
PEAK
A
= 1.18kΩ.
= -40°C to +85°C. Typical values are at V
SYMBOL
t_
t_
t_
V
V
t_
t_
V
t_
FLTDLY
t_
BMTH
FAULT
RESET
PMTH
INIT
INIT
BTH
OFF
ON
1
2
BIAS
V
V
V
Time from rising edge of TX_DISABLE to
I
(Note 6)
Time from rising edge of TX_DISABLE to
I
(Note 6)
Time to set V
after rising edge of TX_DISABLE (Note 6)
Time after power-on to transmitter-on with
TX_DISABLE low (Note 6)
Time from fault occurrence to V
high; C
(Note 6)
Time from fault to I
I
Time TX_DISABLE must be held high to
reset FAULT (Note 6)
BIAS
BIAS
MOD
BIASMON
BIAS
PWRMON
from the total current.
= I
and I
= I
referenced to V
FAULT
BIAS_OFF
MOD_OFF
MOD
> V
> V
FAULT
< 20pF, R
PMTH
BMTH
CONDITIONS
at 99% of steady state
and I
(Note 6)
BIAS
= low after power-on or
causes a fault
causes a fault
CC
CC
MOD
= I
FAULT
= +3.3V, TC1 and TC2 are shorted, PEAKSET open, T
BIAS_OFF
CC
= I
, temperature, 3mA < I
= 4.7kΩ
MOD_OFF
FAULT
and
=
-0.250
MIN
0.7
0.7
BIAS
< 15mA.
TYP
-0.2
0.8
0.8
1.8
1.4
55
60
60
1
-0.150
MAX
500
200
200
0.9
0.9
50
5
5
1
UNITS
ms
ms
µs
µs
µs
µs
µs
V
V
V
A
=