L293E STMicroelectronics, L293E Datasheet
L293E
Specifications of L293E
Available stocks
Related parts for L293E
L293E Summary of contents
Page 1
... July 2003 PUSH-PULL FOUR CHANNEL DRIVERS DIP16 L293B sensing resistors, for switchmode control. The L293B and L293E are package in 16 and 20- pin plastic DIPs respectively ; both use the four center pins to conduct heat to the printed circuit board. POWERDIP (16+2+2) - L293E L293B ...
Page 2
... L293E L293B BLOCK DIAGRAMS 2/12 DIP16 - L293B POWERDIP (16+2+2) - L293E ...
Page 3
... SCHEMATIC DIAGRAM (*) In the L293 these points are not externally available. They are internally connected to the ground (substrate). O Pins of L293 () Pins of L293E. ABSOLUTE MAXIMUM RATINGS Symbol V Supply Voltage s V Logic Supply Voltage ss V Input Voltage i V Inhibit Voltage inh I Peak Output Current (non repetitive t = 5ms) ...
Page 4
... Sink Output Saturation Voltage CEsatL V SENS Sensing Voltage (pins 4, 7, 14, 17) t Rise Time r t Fall Time f t Turn-on Delay on t Turn-off Delay off * See figure 1 ** Referred to L293E TRUTH TABLE V (each channel (*) High output impedance (**) Relative to the considerate channel 4/12 Parameter Max. Max. Test Condition ...
Page 5
... Figure 1. Switching Timers Figure 2. Saturation voltage versus Output Current Figure 3. Source Saturation Voltage versus Ambient Temperature Figure 4. Sink Saturation Voltage versus Ambient Temperature Figure 5. Quiescent Logic Supply Current versus Logic Supply Voltage L293E L293B 5/12 ...
Page 6
... L293E L293B Figure 6. Output Voltage versus Input Voltage Figure 7. Output Voltage versus Inhibit Voltage 6/12 APPLICATION INFORMATION Figure 8. DC Motor Controls (with connection to ground and to the supply voltage inh H H Fast Motor Stop Run Free Running X Motor Stop L = Low H = High X = Don’t Care Figure 9 ...
Page 7
... Figure 10. Bipolar Stepping Motor Control L293E L293B 7/12 ...
Page 8
... L293E L293B Figure 11. Stepping Motor Driver with Phase Current Control and Short Circuit Protection 8/12 ...
Page 9
... MOUNTING INSTRUCTIONS The R of the L293B and the L293E can be reduced by soldering the GND pins to a suitable copper th j-amb area of the printed circuit board as shown in figure external heatsink (figure 13). During soldering the pins temperature must not exceed 260°C and the soldering time must not be longer than 12 seconds ...
Page 10
... L293E L293B mm DIM. MIN. TYP. MAX. a1 0.51 0.020 B 0.77 1.65 0.030 b 0 8.5 e 2.54 e3 17.78 F 7.1 I 5.1 L 3.3 Z 1.27 10/12 inch MIN. TYP. MAX. 0.065 0.020 0.010 0.787 0.335 0.100 0.700 0.280 0.201 0.130 0.050 OUTLINE AND MECHANICAL DATA DIP16 ...
Page 11
... MAX. MIN. a1 0.51 0.020 B 0.85 1.40 0.033 b 0.50 b1 0.38 0.50 0.015 D 24.80 E 8.80 e 2.54 e3 22.86 F 7.10 I 5.10 L 3.30 Z 1.27 inch MECHANICAL DATA TYP. MAX. 0.055 0.020 0.020 0.976 0.346 0.100 0.900 0.280 0.201 0.130 0.050 L293E L293B OUTLINE AND Powerdip 20 11/12 ...
Page 12
... L293E L293B Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice ...