L6206N STMicroelectronics, L6206N Datasheet - Page 4

• Manufacturer Part Number: L6206N
• Description: IC DRVR FULL BRDG DUAL 24PWRDIP
• Manufacturer: STMicroelectronics
• Type: H Bridger

Specifications of L6206N

• Input Type: Non-Inverting
• Number Of Outputs: 4
• On-state Resistance: 300 mOhm
• Current - Output / Channel: 2.8A
• Current - Peak Output: 5.6A
• Voltage - Supply: 8 V ~ 52 V
• Operating Temperature: -25°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.300", 7.62mm)
• Operating Temperature Classification: Automotive
• Package Type: PDIP
• Operating Supply Voltage (min): 8V
• Operating Supply Voltage (typ): 48V
• Operating Supply Voltage (max): 52V
• Operating Supply Voltage: 8 V to 52 V
• Supply Current: 0.01 A
• Mounting Style: Through Hole
• Motor Type: Full Bridge
• No. Of Outputs: 4
• Output Current: 2.8A
• Supply Voltage Range: 8V To 52V
• Driver Case Style: DIP
• No. Of Pins: 24
• Operating Temperature Range: -40°C To +150°C
• Svhc: No SVHC
• Rohs Compliant: Yes
• For Use With: 497-4135 - EVAL BOARD FOR L6206 SERIES
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 497-4211-5

L6206
PIN DESCRIPTION
4/23
PowerDIP24
SO24/
18, 19
PIN #
6, 7,
10
11
12
13
14
15
16
17
20
21
1
2
3
4
5
8
9
PACKAGE
PowerSO36
19, 36
PIN #
1, 18,
10
11
12
13
15
22
24
25
26
27
28
29
30
32
33
4
5
PROGCL
SENSE
SENSE
VBOOT
OUT1
OUT1
OUT2
OUT2
Name
OCD
OCD
GND
IN1
IN2
IN1
IN2
EN
VS
VS
B
A
B
A
A
B
B
A
B
A
B
B
A
A
B
B
Power Supply
Power Supply
Power Supply
Power Supply
Power Output
Power Output
Power Output
Power Output
Open Drain
Open Drain
Logic Input
Logic Input
Logic Input
Logic input
Logic input
Voltage
Supply
Output
Output
R Pin
Type
GND
Bridge A Logic Input 1.
Bridge A Logic Input 2.
Bridge A Source Pin. This pin must be connected to Power
Ground directly or through a sensing power resistor.
Bridge A Overcurrent Detection and thermal protection pin.
An internal open drain transistor pulls to GND when
overcurrent on bridge A is detected or in case of thermal
protection.
Bridge A Output 1.
Signal Ground terminals. In Power DIP and SO packages,
these pins are also used for heat dissipation toward the
PCB.
Bridge B Output 1.
Bridge B Overcurrent Detection and thermal protection pin.
An internal open drain transistor pulls to GND when
overcurrent on bridge B is detected or in case of thermal
protection.
Bridge B Source Pin. This pin must be connected to Power
Ground directly or through a sensing power resistor.
Bridge B Input 1
Bridge B Input 2
Bridge B Overcurrent Level Programming. A resistor
connected between this pin and Ground sets the
programmable current limiting value for the bridge B. By
connecting this pin to Ground the maximum current is set.
This pin cannot be left non-connected.
Bridge B Enable. LOW logic level switches OFF all Power
MOSFETs of Bridge B.
If not used, it has to be connected to +5V.
Bootstrap Voltage needed for driving the upper Power
MOSFETs of both Bridge A and Bridge B.
Bridge B Output 2.
Bridge B Power Supply Voltage. It must be connected to
the supply voltage together with pin VS
Bridge A Power Supply Voltage. It must be connected to
the supply voltage together with pin VS
Bridge A Output 2.
Function
A
B
.
.