L6563A STMicroelectronics, L6563A Datasheet - Page 18
![IC PFC CTRLR TRANSITION 14SOIC](/photos/6/57/65750/497-14-soic_sml.jpg)
L6563A
Manufacturer Part Number
L6563A
Description
IC PFC CTRLR TRANSITION 14SOIC
Manufacturer
STMicroelectronics
Datasheet
1.L6563ATR.pdf
(39 pages)
Specifications of L6563A
Mode
Discontinuous (Transition)
Current - Startup
50µA
Voltage - Supply
10.3 V ~ 22 V
Operating Temperature
-25°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Maximum Operating Temperature
+ 150 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 25 C
For Use With
497-9082 - EVAL BOARD L6563 (200W)497-8850 - BOARD EVAL FOR L6563/STW55NM60N497-8834 - BOARD DEMO FOR L6563/LL6566A497-8429 - BOARD ADAPTER L6599/STP12NM50N497-5854 - DEMO BOARD FOR L6563497-5496 - EVAL BOARD FOR L6599497-5493 - EVAL BOARD FOR L6563
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Frequency - Switching
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
L6563A
Manufacturer:
ST
Quantity:
20 000
Part Number:
L6563AD013TR
Manufacturer:
ST
Quantity:
20 000
Application information
6.2
6.3
18/39
Feedback Failure Protection (FFP)
The OVP function above described is able to handle "normal" overvoltage conditions, i.e.
those resulting from an abrupt load/line change or occurring at start-up. It cannot handle the
overvoltage generated, for instance, when the upper resistor of the output divider (R1) fails
open: the voltage loop can no longer read the information on the output voltage and will
force the PFC pre-regulator to work at maximum ON-time, causing the output voltage to rise
with no control.
A pin of the device (PFC_OK) has been dedicated to provide an additional monitoring of the
output voltage with a separate resistor divider (R3 high, R4 low, see
is selected so that the voltage at the pin reaches 2.5V if the output voltage exceeds a preset
value, usually larger than the maximum Vo that can be expected, also including worst-case
load/line transients.
Example: V
then: R4 = 3MΩ ·2.5/(475-2.5) = 15.87kΩ.
When this function is triggered, the gate drive activity is immediately stopped, the device is
shut down, its quiescent consumption is reduced below 250 µA and the condition is latched
as long as the supply voltage of the IC is above the UVLO threshold. At the same time the
pin PWM_LATCH is asserted high. PWM_LATCH is an open source output able to deliver
3.7V min. with 0.5 mA load, intended for tripping a latched shutdown function of the PWM
controller IC in the cascaded DC-DC converter, so that the entire unit is latched off. To
restart the system it is necessary to recycle the input power, so that the Vcc voltages of both
the L6563/A and the PWM controller go below their respective UVLO thresholds.
The PFC_OK pin doubles its function as a not-latched IC disable: a voltage below 0.2V will
shut down the IC, reducing its consumption below 1 mA. In this case both PWM_STOP and
PWM_LATCH keep their high impedance status. To restart the IC simply let the voltage at
the pin go above 0.26 V.
Note that this function offers a complete protection against not only feedback loop failures or
erroneous settings, but also against a failure of the protection itself. Either resistor of the
PFC_OK divider failing short or open or a PFC_OK pin floating will result in shutting down
the IC and stopping the pre-regulator.
Voltage Feedforward
The power stage gain of PFC pre-regulators varies with the square of the RMS input
voltage. So does the crossover frequency f
has a single pole characteristic. This leads to large trade-offs in the design.
For example, setting the gain of the error amplifier to get f
having f
control loop causes large transient current flow during rapid line or load changes that are
limited by the dynamics of the multiplier output. This limit is considered when selecting the
sense resistor to let the full load power pass under minimum line voltage conditions, with
some margin. But a fixed current limit allows excessive power input at high line, whereas a
fixed power limit requires the current limit to vary inversely with the line voltage.
Voltage Feedforward can compensate for the gain variation with the line voltage and allow
overcoming all of the above-mentioned issues. It consists of deriving a voltage proportional
to the input RMS voltage, feeding this voltage into a squarer/divider circuit (1/V
and providing the resulting signal to the multiplier that generates the current reference for
the inner current control loop (see
c
≅ 4 Hz @ 88 Vac, resulting in a sluggish control dynamics. Additionally, the slow
O
= 400 V, Vox = 475V. Select: R3 = 3MΩ;
Figure
35).
c
of the overall open-loop gain because the gain
c
= 20 Hz @ 264 Vac means
Figure
34). This divider
L6563 - L6563A
2
corrector)