ISL6443AIRZ-TK Intersil, ISL6443AIRZ-TK Datasheet - Page 12
![IC CTRLR SGL/STP DWN PWM 28-QFN](/photos/7/54/75412/isl6540acrz-t_sml.jpg)
ISL6443AIRZ-TK
Manufacturer Part Number
ISL6443AIRZ-TK
Description
IC CTRLR SGL/STP DWN PWM 28-QFN
Manufacturer
Intersil
Datasheet
1.ISL6443AIRZ.pdf
(19 pages)
Specifications of ISL6443AIRZ-TK
Applications
Power Supplies
Current - Supply
2mA
Voltage - Supply
5.6 V ~ 24 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Out-of-Phase Operation
The two PWM controllers in the ISL6443A operate 180
out-of-phase to reduce input ripple current. This reduces the
input capacitor ripple current requirements, reduces power
supply-induced noise and improves EMI. This effectively helps
to lower component cost, save board space and reduce EMI.
Dual PWMs typically operate in-phase and turn on both upper
FETs at the same time. The input capacitor must then support
the instantaneous current requirements of both controllers
simultaneously, resulting in increased ripple voltage and
current. The higher RMS ripple current lowers the efficiency
due to the power loss associated with the ESR of the input
capacitor. This typically requires more low-ESR capacitors in
parallel to minimize the input voltage ripple and ESR-related
losses, or to meet the required ripple current rating.
With dual synchronized out-of-phase operation, the high-side
MOSFETs of the ISL6443A turn on 180
instantaneous input current peaks of both regulators no longer
overlap, resulting in reduced RMS ripple current and input
voltage ripple. This reduces the required input capacitor ripple
current rating, allowing fewer or less expensive capacitors, and
reducing the shielding requirements for EMI. The “Typical
Performance Curves Oscilloscope Plots are Taken Using the
ISL6443A EVAL Evaluation Board, VIN = 12V Unless
Otherwise Noted.” on page 8 show the synchronized 180° out-
of-phase operation.
Input Voltage Range
The ISL6443A is designed to operate from input supplies
ranging from 4.5V to 24V. However, the input voltage range
can be effectively limited by the available maximum duty
cycle (D
where,
V
discharge path, including the lower FET, inductor and PC
board.
V
including the upper FET, inductor and PC board resistances.
The maximum input voltage and minimum output voltage is
limited by the minimum on-time (t
where, t
Gate Control Logic
The gate control logic translates generated PWM signals into
gate drive signals, which provides amplification, level shifting
and shoot-through protection. The gate drivers have some
circuitry that helps optimize the ICs performance over a wide
range of operational conditions. As MOSFET switching times
can vary dramatically from type to type and with input voltage,
V
V
IN min
d1
d2
IN max
(
= Sum of the parasitic voltage drops in the inductor
= Sum of the voltage drops in the charging path,
(
)
ON(min)
MAX
)
=
≤
⎛
⎝
--------------------------------------------------- -
t
ON min
V
--------------------------------
= 93%).
OUT
(
0.93
= 30ns
V
+
OUT
)
V
×
d1
300kHz
⎞
⎠
+
V
d2
12
–
V
d1
ON(min)
o
out-of-phase. The
).
o
(EQ. 3)
(EQ. 4)
ISL6443A
the gate control logic provides adaptive dead time by
monitoring real gate waveforms of both the upper and the lower
MOSFETs. Shoot-through control logic provides a 20ns
deadtime to ensure that both the upper and lower MOSFETs
will not turn on simultaneously and cause a shoot-through
condition.
Gate Drivers
The low-side gate driver is supplied from VCC_5V and
provides a peak sink/source current of 400mA. The high-side
gate driver is also capable of 400mA current. Gate-drive
voltages for the upper N-Channel MOSFET are generated by
the flying capacitor boot circuit. A boot capacitor connected
from the BOOT pin to the PHASE node provides power to the
high side MOSFET driver. To limit the peak current in the IC,
an external resistor may be placed between the UGATE pin
and the gate of the external MOSFET. This small series
resistor also damps any oscillations caused by the resonant
tank of the parasitic inductances in the traces of the board and
the FET’s input capacitance.
At start-up, the low-side MOSFET turns on and forces PHASE
to ground in order to charge the BOOT capacitor to 5V. After the
low-side MOSFET turns off, the high-side MOSFET is turned
on by closing an internal switch between BOOT and UGATE.
This provides the necessary gate-to-source voltage to turn on
the upper MOSFET, an action that boosts the 5V gate drive
signal above V
MOSFET is drawn from the internal 5V regulator.
Protection Circuits
The converter output is monitored and protected against
overload, short circuit and undervoltage conditions. A
sustained overload on the output sets the PGOOD low and
initiates hiccup mode.
Overcurrent Protection
Both PWM controllers use the lower MOSFET’s ON-resistance,
r
voltage drop is compared with a threshold set by a resistor
connected from the OCSETx pin to ground.
DS(ON)
, to monitor the current in the converter. The sensed
ISL6443A
VCC_5V
UGATE
PHASE
IN
BOOT
. The current required to drive the upper
FIGURE 15. GATE DRIVER
VIN
June 2, 2008
FN6600.2