MCZ34702EWR2 Freescale Semiconductor, MCZ34702EWR2 Datasheet - Page 32
![IC PWR SUPPLY 3A SW 32-SOIC](/photos/39/29/392938/soic32-w_sml.jpg)
MCZ34702EWR2
Manufacturer Part Number
MCZ34702EWR2
Description
IC PWR SUPPLY 3A SW 32-SOIC
Manufacturer
Freescale Semiconductor
Datasheet
1.MC34702EK.pdf
(39 pages)
Specifications of MCZ34702EWR2
Applications
Controller, Power QUICC™ I, II
Voltage - Input
2.8 ~ 6 V
Number Of Outputs
2
Voltage - Output
7.75V, 0.8 ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-SOIC (7.5mm Width)
Output Current
3 A
Input Voltage
2.8 V to 6 V
Switching Frequency
300 KHz
Mounting Style
SMD/SMT
Duty Cycle (max)
95 %
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Linear Regulator Current Limit
Description section, the current limit of the linear regulator
can be adjusted by means of an external current sense
resistor R
current flowing through the current sense resistor R
sensed between the LDO and the CS pins. When the sensed
voltage exceeds 50mV (typical), the current limit timer starts
to time out while the control circuit limits the output current. If
the over-current condition lasts for more than 10ms, the linear
regulator is shut off and turned on again after 100ms. This
type of operation provides equivalent protection to the analog
“current foldback” operation.
load which can be supplied by the by the linear regulator is
limited by the setting of the LDO current limit. During the
power-up period, the linear regulator operates in the current
limit, supplying the current into the load of the LDO, which
includes all the capacitors connected to the regulator output.
If the total amount load is so large that the regulator could not
reach its regulation voltage in 10ms during the power-up, it
turns off and tries to power up again after 100ms. This
situation may lead to the power-up oscillations.
Linear Regulator External MOSFET
MOSFET to provide a pass element for the power path. The
selection of the proper type of the external power MOSFET is
critical for optimum performance and safe operation of the
linear regulator.
charge, capacitances and transconductance are important
parameters for the stable operation of the linear regulator
while the package of the power MOSFET determines the
maximum power dissipation, and hence the maximum output
current for the required input-to-output voltage drop. The
power dissipation of the external MOSFET can be calculated
from the simple formula:
for the 34702 linear regulator, their typical power dissipation,
and thermal resistance junction-to-case.
32
34702
Table 10. Recommended Power MOSFETs
TYPICAL APPLICATIONS
MTD20N03HDL
As described in the Linear Regulator Functional
It is important to keep in mind that the amount of capacitive
The linear regulator uses an external N-channel power
The power MOSFET’s threshold voltage, R
Where P
Table 10
IRL2703S
Part No.
VIN is the LDO input voltage,
VLDO is the LDO output voltage,
ILDO is the LDO output load current.
S
. The voltage drop caused by the regulator output
D(Q)
shows the recommended power MOSFET types
P
D Q
is the power MOSFET power dissipation
( )
Package
D2PAK
DPAK
=
I
LDO
×
(
V
IN
Typ. P
1.75W*
2.0W
–
V
LDO
D
)
DS(ON)
1.67°C/W
3.3°C/W
R
thJ-C
S
is
, gate
maximum operating junction temperature T
power dissipation in the given application can be calculated
from the following expression:
PCB Layout Considerations
plays a critical role in the overall power regulator
performance. While good careful printed circuit board layout
significantly improves regulation parameters and
electromagnetic compatibility (EMC) performance of the
switching regulator, poor layout practices can lead not only to
significant degradation of regulation and EMC parameters
but even to total dysfunction of the whole regulator IC.
of the regulator circuit. In order to avoid any inductive or
capacitive coupling of the switching regulator noise into the
sensitive analog control circuits, the noisy power ground and
the clean quiet signal ground should be well separated on the
printed circuit board, and connected only at one connection
point. The power routing should be made by heavy traces or
areas of copper. The power path and its return should be
placed, if possible, atop each other on the different layers or
opposite sides of the PC board. The switching regulator input
and output capacitors should be physically placed very close
to the power pins (VIN2, SW, PGND) of the 34702 switching
regulator; and their ground pins, together with the 34702
power ground pins (PGND), should be connected by a single
island of the power ground copper to create the “single-point”
grounding.
grounding concept. The bootstrap capacitor C
tightly connected to the integrated circuit as well.
*When mounted to an FR4 using 0.5 sq.in. drain pad size
The maximum power dissipation is limited by the
Where P
As with any power application, the proper PCB layout
Extreme care should be taken when laying out the ground
NOTE: Freescale does not assume liability, endorse, or warrant
components from external manufacturers referenced in figures
or tables. Although Freescale offers component
recommendations, it is the customer’s responsibility to validate
their application.
allowed dissipation,
T
junction temperature,
T
R
junction-to-case,
R
R
the PC board.
JMAX
A
thJC
thCB
thBA
Figure 32
D(Q)max
is the ambient temperature,
P
D Q
is the power MOSFET maximum operating
is the power MOSFET thermal resistance
is the thermal resistance board-to-ambient of
is the thermal resistance case-to-board,
( )max
is the power MOSFET maximum
illustrates the 34702 switching regulator
Analog Integrated Circuit Device Data
≤
-------------------------------------------------------- -
R
thJC
T
+
JMAX
R
thCB
Freescale Semiconductor
–
T
+
A
R
thBA
JMAX
b
. The allowed
should be