ADP1621ARMZ-R7 Analog Devices Inc, ADP1621ARMZ-R7 Datasheet - Page 7

• Manufacturer Part Number: ADP1621ARMZ-R7
• Description: IC CTRLR DC/DC PWM STEPUP 10MSOP
• Manufacturer: Analog Devices Inc
• Type: Step-Up (Boost)r

Specifications of ADP1621ARMZ-R7

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Current - Output: 1A
• Frequency - Switching: 100kHz ~ 1.5MHz
• Voltage - Input: 2.9 ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Primary Input Voltage: 5.5V
• No. Of Outputs: 1
• Output Current: 1A
• No. Of Pins: 10
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 1 - Unlimited
• Frequency Max: 1.5MHz
• Termination Type: SMD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ADP1621-EVALZ - BOARD EVALUATION FOR ADP1621
• Voltage - Output: -
• Power - Output: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: ADP1621ARMZ-R7; ADP1621ARMZ-R7TR

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
Mnemonic
SDSN
GND
COMP
FB
FREQ
PGND
GATE
PIN
CS
IN
Shutdown and Synchronization Input. Turn the ADP1621 on by driving SDSN high; turn it off by driving SDSN low.
If SDSN is left floating or when the SDSN is pulled low, the ADP1621 goes into shutdown after 50 μs. If synchronization is
needed, synchronize the switching frequency to an external clock by connecting the external clock to the SDSN
pin. An internal 100 kΩ pull-down resistor is connected from SDSN to GND.
Ground.
Regulation Control Compensation Node. COMP is the output of the internal transconductance error amplifier.
Connect a series RC from COMP to GND to compensate the regulator. The nominal voltage range for this pin is
1.0 V to 2.0 V.
Feedback Input. FB is the input to the internal transconductance error amplifier. Drive FB from the output voltage
through a resistive voltage divider. The ratio of the voltage divider sets the output voltage. The regulation voltage
at FB is nominally 1.215 V.
Frequency Control Input. Connect a resistor from FREQ to GND to set the free-running switching frequency
between 100 kHz and 1.5 MHz. The nominal voltage of this pin is 1.4 V.
Power Ground Input. PGND is the ground return for the internal gate driver and the negative input of the internal
current-sense amplifier. Connect PGND to GND as close to the ADP1621 as possible.
Gate Driver Output. The maximum gate driver output is equal to the PIN voltage. GATE drives the gate of the
external n-channel power MOSFET. Connect GATE to the gate of the MOSFET.
Power Input. PIN powers the gate driver output. An internal 5.5 V shunt regulator is connected to this pin. Bypass
PIN to PGND with a 0.1 μF or greater capacitor.
Current-Sense Input. CS is the positive input of the current-sense amplifier. When GATE is turned on, the voltage at
the CS pin increases linearly from 0 V to a maximum of 116 mV, and the nominal peak slope-compensation output
current is 70 μA. When GATE is off, the CS function is disabled. For current sensing in lossless mode, connect CS to
the drain of the power MOSFET. The absolute maximum voltage at CS is 33 V. For higher accuracy current sensing
or higher switch-node voltages, connect CS to a current-sense power resistor in the source of the power MOSFET.
In both sensing methods, it is required to add a slope-compensation resistor, R
in the inductor current for duty cycles greater than 50%. However, it is recommended to add R
because load transients can momentarily cause the duty cycle to be greater than 50%, even when the steady-
state duty cycle is less than 50%.
Input Voltage. IN powers the ADP1621 internal circuitry. An internal 5.5 V shunt regulator is connected to this pin.
Bypass IN to GND with a 0.1 μF or greater capacitor.
Description
COMP
SDSN
FREQ
GND
FB
Figure 4. Pin Configuration
1
2
3
4
5
Rev. A | Page 7 of 32
(Not to Scale)
ADP1621
TOP VIEW
10
9
8
7
6
IN
CS
PIN
GATE
PGND
S
, to the CS pin to achieve stability
S
for all duty cycles
ADP1621