KS8993F-A1 Micrel Inc, KS8993F-A1 Datasheet - Page 13

• Manufacturer Part Number: KS8993F-A1
• Description: IC CONV MED 10/100 3PORT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KS8993F-A1

• Applications: *
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• For Use With: KS8993F-EVAL - EVAL KIT EXPERIMENTAL KS8993F
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

KS8993F
August 26, 2004
Pin #
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
Pin Name
ML_EN
DIAGF
PWRDN
AGND
VDDA
AGND
MUX1
MUX2
AGND
VDDA
FXSD1
RXP1
RXM1
AGND
TXP1
TXM1
VDDATX
VDDARX
RXM2
RXP2
AGND
TXM2
TXP2
VDDA
AGND
TEST1
TEST2
ISET
AGND
VDDAP
AGND
X1
X2
RST_N
BPEN
SMAC
LEDSEL0
SMTXEN
Type
Ipd
Ipd
I
Gnd
Pwr
Gnd
I
I
Gnd
Pwr
I
I/O
I/O
Gnd
I/O
I/O
Pwr
Pwr
I/O
I/O
Gnd
I/O
I/O
Pwr
Gnd
I
I
O
Gnd
Pwr
Gnd
I
O
Ipu
Ipd
Ipd
Ipd
Ipd
Description
1 = enable missing link
0 = disable missing link
1 = diagnostic fail
0 = diagnostic normal
Chip power down input (active low)
Analog ground
1.8V analog VDD
Analog ground
Factory test pin – float for normal operation
Factory test pin – float for normal operation
Analog ground
1.8V analog VDD
Fiber signal detect / factory test pin
Physical receive or transmit signal (+ differential)
Physical receive or transmit signal (- differential)
Analog ground
Physical transmit or receive signal (+ differential)
Physical transmit or receive signal (- differential)
3.3V or 2.5V analog VDD
3.3V or 2.5V analog VDD
Physical receive or transmit signal (– differential)
Physical receive or transmit signal (+ differential)
Analog ground
Physical transmit or receive signal (– differential)
Physical transmit or receive signal (+ differential)
1.8V analog VDD
Analog ground
Factory test pin – float for normal operation
Factory test pin – float for normal operation
Set physical transmit output current.
Pull down this pin with a 3.01K 1% resistor to ground.
Analog ground
1.8V analog VDD for PLL
Analog ground
25 MHz crystal/oscillator clock connections
Note: Clock is +/- 50ppm for both crystal and oscillator.
Hardware reset pin (active low)
Half Duplex Backpressure
Special Mac Mode
LED display mode select
See description in pin# (1,4).
Switch MII transmit enable
result.
Pins (X1, X2) connect to a crystal. If an oscillator is used, X1 connects
to a 3.3V tolerant oscillator and X2 is a no connect.
1 = enable
0 = disable
1 = enable
0 = disable
In this mode, the switch will do faster backoffs than normal.
- 13 -
Revision 1.0
Micrel