MT18VDDF12872G-335D3 Micron Technology Inc, MT18VDDF12872G-335D3 Datasheet - Page 12

no-image

MT18VDDF12872G-335D3

Manufacturer Part Number
MT18VDDF12872G-335D3
Description
MODULE DDR SDRAM 1GB 184-DIMM
Manufacturer
Micron Technology Inc
Datasheet

Specifications of MT18VDDF12872G-335D3

Memory Type
DDR SDRAM
Memory Size
1GB
Speed
167MHz
Package / Case
184-DIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
557-1113
the DLL, it should always be followed by a LOAD
MODE REGISTER command to select normal operat-
ing mode.
reserved for future use and/or test modes. Test modes
and reserved states should not be used because
unknown operation or incompatibility with future ver-
sions may result.
Extended Mode Register
beyond those controlled by the mode register; these
additional functions are DLL enable/disable and out-
put drive strength. These functions are controlled via
the bits shown in the Extended Mode Register Defini-
tion Diagram. The extended mode register is pro-
grammed via the LOAD MODE REGISTER command
to the mode register (with BA0 = 1 and BA1 = 0) and
will retain the stored information until it is pro-
grammed again or the device loses power.
enabling of the DLL should always be followed by a
LOAD MODE REGISTER command to the mode regis-
ter (BA0/BA1 both LOW) to reset the DLL.
all device banks are idle and no bursts are in progress,
and the controller must wait the specified time before
initiating any subsequent operation. Violating either
of these requirements could result in unspecified oper-
ation.
pdf: 09005aef8074e85b, source: 09005aef8072fe49
DDF18C64_128x72G.fm - Rev. C 11/04 EN
All other combinations of values for A7–A12 are
The extended mode register controls functions
The extended mode register must be loaded when
The
12
DLL Enable/Disable
DLL enable is required during power-up initialization
and upon returning to normal operation after having
disabled the DLL for the purpose of debug or evalua-
tion. (When the device exits self refresh mode, the DLL
is enabled automatically.) Any time the DLL is enabled,
a DLL Reset and 200 clock cycles with CKE HIGH must
occur before a READ command can be issued.
NOTE:
1. BA1 and BA0 (E14 and E13) must be “0, 1” to select the
2. QFC# is not supported.
E12
0
The DLL must be enabled for normal operation.
Extended Mode Register (vs. the base Mode Register).
Figure 8: Extended Mode Register
E11
0 1
14
BA1 BA0
0
Micron Technology, Inc., reserves the right to change products or specifications without notice.
184-PIN DDR SDRAM RDIMM
1 1
E10
13
0
E9
12
512MB, 1GB (x72, ECC, SR)
A12
0
11
E8
A11
0
Definition Diagram
E7
10
0
A10
Operating Mode
E6 E5
0
9
A9
0
8
A8
E4
0
7
A7 A6 A5 A4 A3
E3
0
6
E2 2
0
5
©2004 Micron Technology, Inc. All rights reserved.
4
E1,
Valid
3
E0
2
A2 A1 A0
DS
Operating Mode
Reserved
Reserved
1
E1
0
DLL
0
E0
0
1
Drive Strength
Extended Mode
Register (Ex)
Address Bus
Normal
Disable
Enable
DLL

Related parts for MT18VDDF12872G-335D3