MT4VDDT3264HG-335F2 Micron Technology Inc, MT4VDDT3264HG-335F2 Datasheet - Page 19
![MODULE DDR 256MB 200-SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT4VDDT3264HG-335F2
Manufacturer Part Number
MT4VDDT3264HG-335F2
Description
MODULE DDR 256MB 200-SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT4VDDT3264HG-335F2.pdf
(30 pages)
Specifications of MT4VDDT3264HG-335F2
Memory Type
DDR SDRAM
Memory Size
256MB
Speed
333MT/s
Package / Case
200-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Notes
pdf: 09005aef8086ea3d, source: 09005aef8086ea0b
DD4C8_16_32x64HG.fm - Rev. C 9/04 EN
10. I
11. This parameter is sampled. V
1. All voltages referenced to V
2. Tests for AC timing, I
3. Outputs measured with equivalent load:
4. AC timing and I
5. The AC and DC input level specifications are as
6. V
7. V
8. I
9. Enables on-chip refresh and address counters.
characteristics may be conducted at nominal ref-
erence/supply voltage levels, but the related spec-
ifications and device operation are guaranteed for
the full voltage range specified.
swing of up to 1.5V in the test environment, but
input timing is still referenced to V
crossing point for CK/CK#), and parameter speci-
fications are guaranteed for the specified AC input
levels under normal use conditions. The mini-
mum slew rate for the input signals used to test
the device is 1V/ns in the range between V
and V
defined in the SSTL_2 Standard (i.e., the receiver
will effectively switch as a result of the signal
crossing the AC input level, and will remain in that
state as long as the signal does not ring back
above [below] the DC input LOW [HIGH] level).
ting device and to track variations in the DC level
of the same. Peak-to-peak noise (non-common
mode) on V
DC value. Thus, from V
±25mV for DC error and an additional ±25mV for
AC noise. This measurement is to be taken at the
nearest V
system supply for signal termination resistors, is
expected to be set equal to V
variations in the DC level of V
rates. Specified values are obtained with mini-
mum cycle time at CL = 2 for -262, and -26A, CL =
2.5 for -335 and -265 with the outputs open.
properly initialized, and is averaged at the defined
cycle rate.
V
25°C, V
DD
DD
REF
TT
DD
Q = +2.5V ±0.2V, V
is not applied directly to the device. V
is dependent on output loading and cycle
specifications are tested after the device is
is expected to equal V
IH
OUT
(AC).
REF
(DC) = V
REF
Output
(V
by-pass capacitor.
OUT
may not exceed ±2 percent of the
)
DD
DD
V
DD
tests may use a V
TT
REF
50
Q/2, V
30pF
, and electrical AC and DC
Reference
Point
DD
= V
SS
DD
Q/2, V
.
SS
OUT
REF
Q/2 of the transmit-
REF
DD
, f = 100 MHz, T
.
(peak to peak) =
and must track
= +2.5V ±0.2V,
REF
REF
is allowed
(or to the
IL
IL
-to-V
TT
(ACV)
is a
A
IH
=
19
12. For slew rates < 1 V/ns and to 0.5 Vns. If the slew
13. The CK/CK# input reference level (for timing ref-
14. Inputs are not recognized as valid until V
15. The output timing reference level, as measured at
16.
17. The intent of the “Don’t Care” state after comple-
18. This is not a device limit. The device will operate
19. It is recommended that DQS be valid (HIGH or
20. MIN (
21. The refresh period is 64ms. This equates to an
64MB, 128MB, 256MB (x64, SR)
200-PIN DDR SDRAM SODIMM
0.2V. DM input is grouped with I/O pins, reflecting
the fact that they are matched in loading.
rate is < 0.5V/ns, timing must be derated:
an additional 50ps per each 100 mV/ns reduction
in slew rate from 500 mV/ns, while
fected. If the slew rate exceeds 4.5 V/ns, function-
ality is uncertain. For -335, slew rates must be
0.5 V/ns.
erenced to CK/CK#) is the point at which CK and
CK# cross; the input reference level for signals
other than CK/CK# is V
lizes. Exception: during the period before V
stabilizes, CKE 0.3 x V
the timing reference point indicated in Note 3, is
V
t
time windows as valid data transitions. These
parameters are not referenced to a specific voltage
level, but specify when the device output is no
longer driving (HZ) or begins driving (LZ).
tion of the postamble is that the DQS-driven sig-
nal should either be HIGH, LOW, or High-Z and
that any signal transition within the input switch-
ing region must follow valid input requirements. If
DQS transitions HIGH, above DC V
it must not transition LOW, below DC V
t
with a negative value, but system performance
could be degraded due to bus turnaround.
LOW) on or before the WRITE command. The
case shown (DQS going from High-Z to logic
LOW) applies when no WRITEs were previously in
progress on the bus. If a previous WRITE was in
progress, DQS could be HIGH during this time,
depending on
smallest multiple of
absolute value for the respective parameter.
(MAX) for I
ple of
value for
average refresh rate of 15.625µs (64MB) or
7.8125µs (128MB, 256MB). However, an AUTO
REFRESH command must be asserted at least
HZ and
DQSH (MIN).
Micron Technology, Inc., reserves the right to change products or specifications without notice.
TT
.
t
RC or
t
CK that meets the maximum absolute
t
t
LZ transitions occur in the same access
RAS.
DD
t
t
RFC) for I
measurements is the largest multi-
DQSS.
t
CK that meets the minimum
REF
DD
©2004 Micron Technology, Inc. All rights reserved.
DD
Q is recognized as LOW.
.
measurements is the
IH
t
IH is unaf-
(MIN) then
IH
REF
, prior to
t
IS has
stabi-
t
RAS
REF