MT16LSDF3264HG-133G4 Micron Technology Inc, MT16LSDF3264HG-133G4 Datasheet - Page 9
![MODULE SDRAM 256MB 144SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT16LSDF3264HG-133G4
Manufacturer Part Number
MT16LSDF3264HG-133G4
Description
MODULE SDRAM 256MB 144SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT16LSDF6464HY-13ED2.pdf
(22 pages)
Specifications of MT16LSDF3264HG-133G4
Memory Type
SDRAM
Memory Size
256MB
Speed
133MHz
Package / Case
144-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Table 7:
NOTE:
pdf: 09005aef807924d2, source: 09005aef807924f1
SDF16C32_64x64HG.fm - Rev. E 4/06 EN
LENGTH
1. For full-page accesses: y = 1,024 (both 256MB and
2. For a burst length of two, A1–A9 select the block-of-
3. For a burst length of four, A2–A9 select the block-of-
4. For a burst length of eight, A3–A9 select the block-of-
5. For a full-page burst, the full row is selected and A0–A9
6. Whenever a boundary of the block is reached within a
7. For a burst length of one, A0–A9 select the unique col-
BURST
Page
Full
(y)
512MB modules)
two burst; A0 selects the starting column within the
block.
four burst; A0–A1 select the starting column within the
block.
eight burst; A0–A2 select the starting column within
the block.
select the starting column.
given sequence above, the following access wraps
within the block.
umn to be accessed, and mode register bit M3 is
ignored.
2
4
8
A2 A1 A0
STARTING
ADDRESS
n = A0-A9
COLUMN
0
0
0
0
1
1
1
1
(location
0-y)
A1 A0
0
0
1
1
0
0
1
1
0
0
1
1
Burst Definition Table
A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Cn, Cn + 1, Cn + 2
Cn + 3, Cn + 4...
0-1-2-3-4-5-6-7
1-2-3-4-5-6-7-0
2-3-4-5-6-7-0-1
3-4-5-6-7-0-1-2
4-5-6-7-0-1-2-3
5-6-7-0-1-2-3-4
6-7-0-1-2-3-4-5
7-0-1-2-3-4-5-6
…Cn - 1, Cn…
SEQUENTIAL
TYPE =
0-1-2-3
1-2-3-0
2-3-0-1
3-0-1-2
ORDER OF ACCESSES
0-1
1-0
WITHIN A BURST
INTERLEAVED
0-1-2-3-4-5-6-7
1-0-3-2-5-4-7-6
2-3-0-1-6-7-4-5
3-2-1-0-7-6-5-4
4-5-6-7-0-1-2-3
5-4-7-6-1-0-3-2
6-7-4-5-2-3-0-1
7-6-5-4-3-2-1-0
Not supported
TYPE =
0-1-2-3
1-0-3-2
2-3-0-1
3-2-1-0
0-1
1-0
9
Burst Type
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
mined by the burst length, the burst type, and the
starting column address, as shown in Table 7.
CAS Latency (CL)
tion of a READ command and the availability of the
first piece of output data. The latency can be set to two
or three clocks.
and the latency is m clocks, the data will be available
by clock edge n + m. The DQ will start driving as a
result of the clock edge one cycle earlier (n + m - 1),
and provided that the relevant access times are met,
the data will be valid by clock edge n + m. For example,
assuming that the clock cycle time is such that all rele-
vant access times are met, if a READ command is regis-
tered at T0 and the latency is programmed to two
clocks, the DQ will start driving after T1 and the data
will be valid by T2, as shown in Figure 4 on page 8.
Table 8 on page 10 indicates the operating frequencies
at which each CL setting can be used.
operation or incompatibility with future versions may
result.
COMMAND
COMMAND
Accesses within a given burst may be programmed
The ordering of accesses within a burst is deter-
CL is the delay, in clock cycles, between the registra-
If a READ command is registered at clock edge n,
Reserved states should not be used as unknown
CLK
CLK
DQ
DQ
Micron Technology, Inc., reserves the right to change products or specifications without notice.
READ
READ
144-PIN SDRAM SODIMM
T0
T0
Figure 5: CL Diagram
256MB, 512MB (x64, DR)
CAS Latency = 2
NOP
NOP
T1
T1
t
t AC
LZ
CAS Latency = 3
©2006 Micron Technology, Inc. All rights reserved.
T2
NOP
T2
NOP
t
t AC
LZ
D
t OH
OUT
T3
T3
NOP
D
t OH
OUT
DON’T CARE
UNDEFINED
T4