MT4LSDT1664AG-133D1 Micron Technology Inc, MT4LSDT1664AG-133D1 Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT4LSDT1664AG-133D1
Manufacturer Part Number
MT4LSDT1664AG-133D1
Description
MODULE SDRAM 128MB 168DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT4LSDT1664AY-133D1.pdf
(28 pages)
Specifications of MT4LSDT1664AG-133D1
Memory Type
SDRAM
Memory Size
128MB
Speed
133MHz
Package / Case
168-DIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Notes
PDF: 09005aef8078bc7c/Source: 09005aef8078bcd3
SD4C4_8_16X64AG.fm - Rev. D 1/07 EN
10.
11. AC timing and I
12. Other input signals are allowed to transition no more than once every two clocks and
13. I
14. Timing actually specified by
15. Timing actually specified by
16. Timing actually specified by
17. Required clocks are specified by JEDEC functionality and are not dependent on any
18. The I
19. Address transitions average one transition every two clocks.
20. CLK must be toggled a minimum of two times during this period.
21. Based on
22. V
1. All voltages referenced to V
2. This parameter is sampled. V
3. I
4. Enables on-chip refresh and address counters.
5. The minimum specifications are used only to
6. An initial pause of 100µs is required after power-up, followed by two AUTO REFRESH
7. AC characteristics assume
8. In addition to meeting the transition rate specification, the clock and CKE must tran-
9. Outputs measured at 1.5V with equivalent load:
f = 1 MHz; T
with minimum cycle time and the outputs open.
indicate cycle time at which proper operation over the full temperature range is
ensured (0°C ≤ T
commands, before proper device operation is ensured. (V
ered up simultaneously. V
REFRESH command wake-ups should be repeated anytime the
ment is exceeded.
sit between V
t
a reference to V
High-Z.
crossover point. If the input transition time is longer than 1ns, then the timing is ref-
erenced at V
are otherwise at valid V
cycle rate.
minimum cycle rate.
timing parameter.
frequency alteration for the test condition.
cannot be greater than one-third of the cycle rate. V
a pulse width ≤3ns.
DD
HZ defines the time at which the output achieves the open circuit condition; it is not
DD
IH
Q
is dependent on output loading and cycle rates. Specified values are obtained
specifications are tested after the device is properly initialized.
overshoot: V
DD
current will increase or decrease proportionally according to the amount of
t
CK = 10ns for -10E;
A
50pF
IL
IH
= 25°C; pin under test biased at 1.4V.
(MAX) and V
32MB, 64MB, 128MB (x64, SR) 168-Pin SDRAM UDIMM
OH
DD
and V
A
IH
≤ +70°C for commercial,
or V
tests have V
(MAX) = V
IL
OL
IH
(or between V
. The last valid data element will meet
SS
or V
t
20
SS
T = 1ns.
IH
and V
t
t
t
.
DD
CKS; clock(s) specified as a reference only at minimum
WR plus
WR.
DD
(MIN) and no longer at the ISV crossover point.
t
IL
CK = 7.5ns for -133 and -13E.
IL
, V
Q + 2V for a pulse width ≤3ns, and the pulse width
levels.
= 0V and V
SS
DD
Q must be at same potential.) The two AUTO
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Q = +3.3V;
IL
t
RP; clock(s) specified as a reference only at
and V
–
IH
40°C ≤ T
IH
= 3V, with timing referenced to 1.5V
) in a monotonic manner.
IL
A
undershoot: V
≤ +85°C for industrial).
DD
©2002 Micron Technology, Inc. All rights reserved.
and V
t
t
OH before going
REF refresh require-
DD
IL
Q must be pow-
(MIN) =
Notes
–
2V for