MT9HVF12872PKY-667A1 Micron Technology Inc, MT9HVF12872PKY-667A1 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT9HVF12872PKY-667A1
Manufacturer Part Number
MT9HVF12872PKY-667A1
Description
MODULE DDR2 1GB 244-MDIMM VLP
Manufacturer
Micron Technology Inc
Datasheet
1.MT9HVF12872KY-53EA1.pdf
(17 pages)
Specifications of MT9HVF12872PKY-667A1
Memory Type
DDR2 SDRAM
Memory Size
1GB
Speed
667MT/s
Package / Case
244-MDIMM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 6:
PDF: 09005aef81c9620b/Source: 09005aef81c961ec
HVF9C64_128x72K.fm - Rev. C 3/07 EN
RAS#, CAS#, WE#
(RDQS0–RDQS8)
DQS0#–DQS8#
DQS0–DQS8,
DQ0–DQ63
DM0–DM8
CK0, CK0#
V
BA0, BA1
BA0–BA2
SA0–SA2
CB0–CB7
Symbol
(512MB)
E
A0–A13
RESET#
DD
P
RR
ODT0
(1GB)
CKE0
SDA
AR
S0#
SCL
/V
_O
_I
DD
N
UT
Q
Pin Descriptions
(open drain)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
Output
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
I/O
On-die termination: ODT (registered HIGH) enables termination resistance internal to
the DDR2 SDRAM. When enabled, ODT is only applied to each of the following pins: DQ,
DQS, DQS#, RDQS, RDQS#, CB, and DM. The ODT input will be ignored if disabled via the
LOAD MODE (LM) command.
Clock: CK and CK# are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of CK#. Output data
(DQs and DQS/DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates
clocking circuitry on the DDR2 SDRAM.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when S# is registered HIGH. S# provides for external
rank selection on systems with multiple ranks. S# is considered part of the command code.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being
entered.
Bank address inputs: BA0–BA1/BA2 define to which device bank an ACTIVE, READ,
WRITE, or PRECHARGE command is being applied. BA0–BA1/BA2 define which mode
register, including MR, EMR, EMR(2), and EMR(3), is loaded during the LM command.
Address inputs: Provide the row address for ACTIVE commands, and the column address
and auto precharge bit (A10) for READ/WRITE commands, to select one location out of the
memory array in the respective bank. A10 sampled during a PRECHARGE command
determines whether the PRECHARGE applies to one device bank (A10 LOW, device bank
selected by BA0–BA1/BA2) or all device banks (A10 HIGH). The address inputs also provide
the op-code during a LM command.
Parity bit for the address and control bus.
Serial clock for presence-detect: SCL is used to synchronize the presence-detect data
transfer to and from the module.
Presence-detect address inputs: These pins are used to configure the presence-detect
device.
Asynchronously forces all registered outputs LOW when RESET# is LOW. This signal can be
used during power-up to ensure that CKE is LOW and DQs are High-Z.
Data input/output: Bidirectional data bus.
Data strobe: Output with read data, input with write data for source synchronous
operation. Edge-aligned with read data, center-aligned with write data. DQS# is only used
when differential data strobe mode is enabled via the LM command. DQS9#–DQS17# are
only used when RDQS# is enabled via the LM command.
Input data mask: DM is an input mask signal for write data. Input data is masked when
DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on
both edges of DQS. Although DM pins are input-only, the DM loading is designed to match
that of DQ and DQS pins. If RDQS is enabled, DQS0#–DQS8# are used only during the READ
command. If RDQS is disabled, RDQS0–RDQS8 become DM0–DM8 and RDQS0#–RDQS8# are
not used.
Check bits.
Serial presence-detect data: SDA is a bidirectional pin used to transfer addresses and
data into and out of the presence-detect portion of the module.
Parity error found on the address and control bus.
Power supply: 1.8V ±0.1V.
512MB, 1GB: (x72, ECC, SR) 244-Pin DDR2 VLP Mini-RDIMM
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Description
Pin Assignments and Descriptions
©2005 Micron Technology, Inc. All rights reserved.