AFBR-5905EZ Avago Technologies US Inc., AFBR-5905EZ Datasheet - Page 4
AFBR-5905EZ
Manufacturer Part Number
AFBR-5905EZ
Description
TXRX ATM/SONET OC-3 2X5
Manufacturer
Avago Technologies US Inc.
Datasheet
1.AFBR-5905Z.pdf
(13 pages)
Specifications of AFBR-5905EZ
Wavelength
1308nm
Data Rate
*
Applications
General Purpose
Voltage - Supply
3.135 V ~ 3.465 V
Connector Type
MTRJ
Mounting Type
Through Hole
Function
MMC OC-3 PB-Free MTRFJ
Product
Transceiver
Maximum Rise Time
3 ns, 2.2 ns
Maximum Fall Time
3 ns, 2.2 ns
Pulse Width Distortion
0.21 ns, 0.15 ns
Maximum Output Current
50 mA
Operating Supply Voltage
3.135 V to 3.465 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
For Use With
Multimode Glass
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Pin Descriptions:
Pin 1 Receiver Signal Ground VEE RX:
Directly connect this pin to the receiver ground plane.
Pin 2 Receiver Power Supply VCC RX:
Provide +3.3 V dc via the recommended receiver power
supply filter circuit. Locate the power supply filter circuit
as close as possible to the VCC RX pin.
Pin 3 Signal Detect SD:
Normal optical input levels to the receiver result in a logic
“1” output. Low optical input levels to the receiver result in
a fault condition indicated by a logic “0” output. This Sig-
nal Detect output can be used to drive a PECL input on
an upstream circuit, such as Signal Detect input or Loss of
Signal-bar.
Pin 4 Receiver Data Out Bar RD-:
No internal terminations are provided. See recommended
circuit schematic.
Pin 5 Receiver Data Out RD+:
No internal terminations are provided. See recommended
circuit schematic.
44
Figure 3. Pin Out Diagram.
RECEIVER SIGNAL GROUND
Pin Descriptions:
Pin 1 Receiver Signal Ground V
Directly connect this pin to the
receiver ground plane.
Pin 2 Receiver Power Supply V
RX:
Provide +3.3 V dc via the
recommended receiver power
supply filter circuit. Locate
the power supply filter circuit
as close as possible to the V
RX pin.
Pin 3 Signal Detect SD:
Normal optical input levels to
the receiver result in a logic
“1” output.
Low optical input levels to the
receiver result in a fault
condition indicated by a logic
“0” output.
This Signal Detect output can
be used to drive a PECL input
on an upstream circuit, such
as Signal Detect input or Loss
of Signal-bar.
Pin 4 Receiver Data Out Bar RD-:
RECEIVER POWER SUPPLY
RECEIVER DATA OUT BAR
RECEIVER DATA OUT
SIGNAL DETECT
o
o
o
o
o
RX
1
2
3
4
5
EE
View
CC
Top
RX:
CC
TX
10
9
8
7
6
o
o
o
o
o
No internal terminations are
provided. See recommended
circuit schematic.
Pin 5 Receiver Data Out RD+:
No internal terminations are
provided. See recommended
circuit schematic.
Pin 6 Transmitter Power Supply
V
Provide +3.3 V dc via the
recommended transmitter
power supply filter circuit.
Locate the power supply filter
circuit as close as possible to
the V
Pin 7 Transmitter Signal Ground
V
Directly connect this pin to the
transmitter ground plane.
Pin 8 Transmitter Disable T
No internal connection.
Optional feature for laser
based products only. For laser
CC
EE
TX:
TRANSMITTER DATA IN BAR
TRANSMITTER DATA IN
TRANSMITTER DISABLE (LASER BASED PRODUCTS ONLY)
TRANSMITTER SIGNAL GROUND
TRANSMITTER POWER SUPPLY
TX:
CC
Mounting Studs/
Solder Posts
TX pin.
Pin 6 Transmitter Power Supply VCC TX:
Provide +3.3 V dc via the recommended transmitter power
supply filter circuit. Locate the power supply filter circuit
as close as possible to the VCC TX pin.
Pin 7 Transmitter Signal Ground VEE TX:
Directly connect this pin to the transmitter ground plane.
Pin 8 Transmitter Disable TDIS:
No internal connection. Optional feature for laser based
products only. For laser based products connect this pin
to +3.3 V TTL logic high “1” to disable module. To enable
module connect to TTL logic low “0”.
Pin 9 Transmitter Data In TD+:
No internal terminations are provided. See recommended
circuit schematic.
Pin 10 Transmitter Data In Bar TD-:
No internal terminations are provided. See recommended
circuit schematic.
Mounting Studs/Solder Posts
The mounting studs are provided for transceiver mechani-
cal attachment to the circuit board. It is recommended
that the holes in the circuit board be connected to chassis
ground.
DIS
:
based products connect this
pin to +3.3 V TTL logic high
“1” to disable module. To
enable module connect to TTL
logic low “0”.
Pin 9 Transmitter Data In TD+:
No internal terminations are
provided. See recommended
circuit schematic.
Pin 10 Transmitter Data In Bar TD-:
No internal terminations are
provided. See recommended
circuit schematic.
Mounting Studs/Solder Posts
The mounting studs are
provided for transceiver
mechanical attachment to the
circuit board. It is
recommended that the holes in
the circuit board be connected
to chassis ground.