JW075A1 Lineage Power, JW075A1 Datasheet - Page 15

• Manufacturer Part Number: JW075A1
• Description: CONVERTER DC/DC 5V 75W OUT
• Manufacturer: Lineage Power
• Series: JW075r
• Type: Isolated with Remote On/Offr

Specifications of JW075A1

• Output: 5V
• Number Of Outputs: 1
• Power (watts): 75W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 75V
• Package / Case: 9-DIP Module
• 1st Output: 5 VDC @ 15A
• Size / Dimension: 2.40" L x 2.28" W x 0.50" H (61mm x 57.9mm x 12.7mm)
• Power (watts) - Rated: 75W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 84%
• Approvals: CE, CSA, UL, VDE
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -

Data Sheet
April 2008
Thermal Considerations
Heat Transfer with Heat Sinks
The power modules have through-threaded, M3 x 0.5
mounting holes, which enable heat sinks or cold plates
to attach to the module. The mounting torque must not
exceed 0.56 N-m (5 in.-lb.). For a screw attachment
from the pin side, the recommended hole size on the
customer’s PWB around the mounting holes is
0.130 ± 0.005 inches. If a larger hole is used, the
mounting torque from the pin side must not exceed
0.25 N-m (2.2 in.-lb.).
Thermal derating with heat sinks is expressed by using
the overall thermal resistance of the module. Total mod-
ule thermal resistance ( ca) is defined as the maximum
case temperature rise ( T
power dissipation (P
The location to measure case temperature (T
shown in Figure 26. Case-to-ambient thermal resis-
tance vs. airflow is shown, for various heat sink config-
urations and heights, in Figure 32. These curves were
obtained by experimental testing of heat sinks, which
are offered in the product catalog.
Figure 32. Case-to-Ambient Thermal Resistance
Lineage Power
ca
8
7
6
5
4
3
2
1
0
0
=
Curves; Either Orientation
-------------------- -
(100)
0.5
T
P
C max
,
D
AIR VELOCITY, m/s (ft./min.)
D
(200)
):
1.0
=
C, max
----------------------- -
T
(300)
C
1.5
dc-dc Converters; 36 to 75 Vdc Input, 5 Vdc Output; 50 W to 150 W
P
–
) divided by the module
D
T
A
(continued)
1 1/2 IN. HEAT SINK
1 IN. HEAT SINK
1/2 IN. HEAT SINK
1/4 IN. HEAT SINK
NO HEAT SINK
(400)
2.0
(500)
2.5
C
JW050A, JW075A, JW100A, JW150A Power Modules:
) is
8-1153 (C)
(600)
3.0
These measured resistances are from heat transfer
from the sides and bottom of the module as well as the
top side with the attached heat sink; therefore, the
case-to-ambient thermal resistances shown are gener-
ally lower than the resistance of the heat sink by itself.
The module used to collect the data in Figure 32 had a
thermal-conductive dry pad between the case and the
heat sink to minimize contact resistance. The use of
Figure 32 is shown in the following example.
Example
If an 85 °C case temperature is desired, what is the
minimum airflow necessary? Assume the JW100A
module is operating at V
of 20 A, maximum ambient air temperature of 40 °C,
and the heat sink is 1/2 inch.
Solution
Given: V
Determine P
Then solve the following equation:
Use Figure 32 to determine air velocity for the 1/2 inch
heat sink.
The minimum airflow necessary for the JW100A mod-
ule is 1.3 m/s (260 ft./min.).
ca
ca
ca
I
T
T
Heat sink = 1/2 in.
P
O
=
A
=
=
C
I
D
= 54 V
= 20 A
= 40 °C
= 85 °C
= 17 W
2.6 °C/W
D
----------------------- -
----------------------- -
T
85 40
by using Figure 30:
C
P
17
–
–
D
T
A
I
= 54 V and an output current
15