LTM4601AEV-1#PBF Linear Technology, LTM4601AEV-1#PBF Datasheet - Page 20
![IC DC/DC UMODULE 12A 133-LGA](/photos/8/70/87000/133-lga_05-08-1755_rev_0_sml.jpg)
LTM4601AEV-1#PBF
Manufacturer Part Number
LTM4601AEV-1#PBF
Description
IC DC/DC UMODULE 12A 133-LGA
Manufacturer
Linear Technology
Series
µModuler
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LTM4601AEVPBF.pdf
(28 pages)
Specifications of LTM4601AEV-1#PBF
Design Resources
LTM4601A-1 Spice Model
Output
0.6 ~ 5 V
Number Of Outputs
1
Power (watts)
60W
Mounting Type
Surface Mount
Voltage - Input
4.5 ~ 20V
Package / Case
133-LGA
1st Output
0.6 ~ 5 VDC @ 12A
Size / Dimension
0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
Power (watts) - Rated
60W
Operating Temperature
-40°C ~ 85°C
Efficiency
95%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS INFORMATION
LTM4601A/LTM4601A-1
Frequency Adjustment
The LTM4601A is designed to typically operate at 850kHz
across most input conditions. The f
open or decoupled with an optional 1000pF capacitor. The
switching frequency has been optimized for maintaining
constant output ripple noise over most operating ranges.
The 850kHz switching frequency and the 400ns minimum
off time can limit operation at higher duty cycles like 5V to
3.3V, and produce excessive inductor ripple currents for
lower duty cycle applications like 20V to 5V. The 5V and
3.3V drop out curves are modifi ed by adding an external
resistor on the f
operation, or higher input voltage operation.
Example for 5V Output
Equations for setting frequency:
I
t
R
• 282ns)) ≈ 886kHz. The inductor ripple current begins
to get high at the higher input voltages due to a larger
voltage across the inductor. This is noted in the “Induc-
tor Ripple Current vs Duty Cycle” graph (Figure 3) where
I
can be lowered at the higher input voltages by adding an
external resistor from f
ing frequency. An 8A ripple current is chosen, and the total
peak current is equal to 1/2 of the 8A ripple current plus
the output current. The 5V output current is limited to 8A,
so the total peak current is less than 12A. This is below the
20
fSET
ON
L
fSET
≈ 10A at 25% duty cycle. The inductor ripple current
LTM4601A minimum on time = 100ns;
t
LTM4601A minimum off time = 400ns; t
where t = 1/Frequency
Duty Cycle = t
ON
= ((4.8 • 10pF)/I
= (V
is 39.2k. Frequency = (V
= ((4.8 • 10pf)/I
IN
/(3 • R
SET
ON
fSET
/t or V
fSET
pin to allow for lower input voltage
)), for 20V operation, I
SET
fSET
), t
to ground to increase the switch-
OUT
)
ON
/V
= 282ns, where the internal
OUT
IN
/(V
SET
IN
pin is normally left
• t
ON
OFF
fSET
)) = (5V/(20
= t – t
= 170μA,
ON
,
14A peak specifi ed value. A 100k resistor is placed from
f
39.2k equates to 28k. The I
20V input voltage equals 238μA. This equates to a t
200ns. This will increase the switching frequency from
~886kHz to ~1.25MHz for the 20V to 5V conversion. The
minimum on time is above 100ns at 20V input. Since
the switching frequency is approximately constant over
input and output conditions, then the lower input voltage
range is limited to 10V for the 1.25MHz operation due to
the 400ns minimum off time. Equation: t
• (1/Frequency) equates to a 400ns on time, and a 400ns
off time. The “V
an operating range of 10V to 20V for 1.25MHz operation
with a 100k resistor to ground, and an 8V to 16V operation
for f
wider input voltage ranges for the 5V output designs while
limiting the inductor ripple current, and maintaining the
400ns minimum off time.
Example for 3.3V Output
Equations for setting frequency:
I
t
R
• 195ns)) ≈ 846kHz. The minimum on time and minimum
off time are within specifi cation at 195ns and 980ns. The
4.5V minimum input for converting 3.3V output will not
meet the minimum off-time specifi cation of 400ns. t
868ns, Frequency = 850kHz, t
SET
fSET
ON
fSET
LTM4601A minimum on time = 100ns;
t
LTM4601A minimum off time = 400ns;
t
Duty Cycle (DC) = t
ON
OFF
= ((3.3 • 10pf)/I
SET
to ground, and the parallel combination of 100k and
= (V
is 39.2k. Frequency = (V
= ((3.3 • 10pF)/I
= t – t
fl oating. These modifi cations are made to provide
IN
/(3 • R
ON
IN
, where t = 1/Frequency
to V
fSET
fSET
OUT
)), for 20V operation, I
ON
fSET
), t
/t or V
Step-Down Ratio” curve refl ects
ON
)
fSET
= 195ns, where the internal
OUT
OFF
OUT
calculation with 28k and
/(V
= 315ns.
/V
IN
IN
• t
ON
ON
)) = (3.3V/(20
fSET
= (V
= 170μA,
OUT
ON
4601afb
/V
ON
IN
of
=
)