APTH006A0X4-SRZ Lineage Power, APTH006A0X4-SRZ Datasheet - Page 15

• Manufacturer Part Number: APTH006A0X4-SRZ
• Description: DC-DC 0.6-3.63V @ 6A
• Manufacturer: Lineage Power
• Series: Pico TLynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of APTH006A0X4-SRZ

• Output: 0.6 ~ 3.63V
• Number Of Outputs: 1
• Power (watts): 21W
• Mounting Type: Surface Mount
• Voltage - Input: 2.4 ~ 5.5V
• Package / Case: 10-SMD Module
• 1st Output: 0.6 ~ 3.63 VDC @ 6A
• Size / Dimension: 0.48" L x 0.48" W x 0.29" H (12.2mm x 12.2mm x 7.3mm)
• Power (watts) - Rated: 21W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Approvals: CSA, EN, UL, VDE
• Product: Non-Isolated / POL
• Output Power: 22 W
• Input Voltage Range: 2.4 V to 5.5 V
• Output Voltage (channel 1): 0.6 V to 3.63 V
• Output Current (channel 1): 6 A
• Output Type: Non-Isolated
• Output Voltage: 0.6 V to 3.63 V
• Output Current: 6A
• Input Voltage: 2.4 to 5.5V
• Screening Level: Industrial
• Mounting Style: Surface Mount
• Pin Count: 10
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Details

Data Sheet
April 7, 2011
Figure 42. Circuit Configuration for margining
Output voltage.
Monotonic Start-up and Shutdown
The Pico TLynx
and shutdown behavior for any combination of rated
input voltage, output current and operating temperature
range.
Startup into Pre-biased Output
The 5.5V Pico TLynx
prebiased output as long as the prebias voltage is 0.5V
less than the set output voltage. Note that prebias
operation is not supported when output voltage
sequencing is used.
Output Voltage Sequencing
The APTH006A0X modules include a sequencing
feature, EZ-SEQUENCE that enables users to
implement various types of output voltage sequencing in
their applications. This is accomplished via an
additional sequencing pin. When not using the
sequencing feature, either tie the SEQ pin to V
leave it unconnected.
When an analog voltage is applied to the SEQ pin, the
output voltage tracks this voltage until the output
reaches the set-point voltage. The final value of the
SEQ voltage must be set higher than the set-point
voltage of the module. The output voltage follows the
voltage on the SEQ pin on a one-to-one volt basis. By
connecting the SEQ pins of multiple modules together,
all modules can track their output voltages to the
voltage applied on the SEQ pin.
For proper voltage sequencing, first, input voltage is
applied to the module. The On/Off pin of the module is
left unconnected (or tied to GND for negative logic
LINEAGE
MODULE
POWER
TM
6A modules have monotonic start-up
Trim
Vo
GND
TM
6A modules can start into a
Rtrim
Q2
Q1
2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 6A output current
Rmargin-down
Rmargin-up
IN
Pico TLynx
or
modules or tied to V
the module is ON by default. After applying input
voltage to the module, a minimum 10msec delay is
required before applying voltage on the SEQ pin. This
delay gives the module enough time to complete its
internal power-up soft-start cycle. During the delay time,
the SEQ pin should be held close to ground (nominally
50mV ± 20 mV). This is required to keep the internal op-
amp out of saturation thus preventing output overshoot
during the start of the sequencing ramp. By selecting
resistor R1 (see fig. 43) according to the following
equation
the voltage at the sequencing pin will be 50mV when
the sequencing signal is at zero.
Figure 43. Circuit showing connection of the
sequencing signal to the SEQ pin.
After the 10msec delay, an analog voltage is applied to
the SEQ pin and the output voltage of the module will
track this voltage on a one-to-one volt bases until the
output reaches the set-point voltage. To initiate
simultaneous shutdown of the modules, the SEQ pin
voltage is lowered in a controlled manner. The output
voltage of the modules tracks the voltages below their
set-point voltages on a one-to-one basis. A valid input
voltage must be maintained until the tracking and output
voltages reach ground potential.
When using the EZ-SEQUENCE
start-up of the module, pre-bias immunity during start-up
is disabled. The pre-bias immunity feature of the
module relies on the module being in the diode-mode
during start-up. When using the EZ-SEQUENCE
feature, modules goes through an internal set-up time of
10msec, and will be in synchronous rectification mode
when the voltage at the SEQ pin is applied. This will
result in the module sinking current if a pre-bias voltage
is present at the output of the module. When pre-bias
immunity during start-up is required, the EZ-
TM
6A: Non-isolated DC-DC Power Modules
VIN+
SEQ
GND
R1
R
1
=
IN
V
499K
for positive logic modules) so that
IN
24950
−
10K
. 0
MODULE
05
TM
ohms,
feature to control
+
-
OUT
TM
15