AXA010A0X3 Lineage Power, AXA010A0X3 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/387/lineage_power_sml.jpg)
AXA010A0X3
Manufacturer Part Number
AXA010A0X3
Description
CONVER DC/DC 0.75 5.5V @ 10A SIP
Manufacturer
Lineage Power
Series
Austin Lynx™r
Type
Point of Load (POL) Non-Isolated with Remote On/Offr
Datasheet
1.AXA010A0X3Z.pdf
(19 pages)
Specifications of AXA010A0X3
Rohs Status
RoHS non-compliant
Output
0.75 ~ 5.5V
Number Of Outputs
1
Power (watts)
55W
Mounting Type
Through Hole
Voltage - Input
10 ~ 14V
Package / Case
10-SIP Module
1st Output
0.75 ~ 5.5 VDC @ 10A
Size / Dimension
2.00" L x 0.32" W x 0.50" H (50.8mm x 8.1mm x 12.7mm)
Power (watts) - Rated
55W
Operating Temperature
-40°C ~ 85°C
Efficiency
93%
Approvals
CSA, EN, UL, VDE
Product
Non-Isolated / POL
3rd Output
-
2nd Output
-
Lead Free Status / Rohs Status
No RoHS Version Available
Other names
555-1013
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AXA010A0X3-SR
Manufacturer:
JAM
Quantity:
1 200
Part Number:
AXA010A0X3-SR
Manufacturer:
LINEAGEPO
Quantity:
20 000
Company:
Part Number:
AXA010A0X3-SRZ
Manufacturer:
SEC
Quantity:
3
Data Sheet
September 30, 2009
Test Configurations
Figure 23. Input Reflected Ripple Current Test
Setup.
Figure 24. Output Ripple and Noise Test Setup.
Figure 25. Output Voltage and Efficiency Test Setup.
LINEAGE
NOTE: All voltage measurements to be taken at the module
V
COM
O
(+)
Efficiency
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
R
R
NOTE: All voltage measurements to be taken at the module
distribution
distribution
POWER
source inductance (L
possible battery impedance. Measure current as shown
above.
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
COPPER STRIP
1uF .
R
R
contact
contact
η =
@ 20°C 100kHz
E.S.R.<0.1Ω
C
Electrolytic
S
GROUND PLANE
1000μF
L
1μH
TEST
V
IN
10uF
V
V
V
COM
TEST
IN
IN
O
(+)
. I
. I
) of 1μH. Capacitor C
12V Austin Lynx
O
IN
SCOPE
10Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc Output;10A Output Current
COM
V
O
Tantalum
2x100μF
C
V
x 100 %
IN
O
RESISTIVE
LOAD
CURRENT PROBE
R
R
S
contact
contact
offsets
V
COM
IN
(+)
R
R
distribution
distribution
R
LOAD
TM
SIP Non-isolated Power Modules, Programmable:
Design Considerations
Input Filtering
The 12V Austin Lynx Programmable SIP module should
be connected to a low ac-impedance source. A highly
inductive source can affect the stability of the module.
An input capacitance must be placed directly adjacent
to the input pin of the module, to minimize input ripple
voltage and ensure module stability.
In a typical application, 4x47 µF low-ESR tantalum
capacitors (AVX part #: TPSE476M025R0100, 47µF
25V 100 mΩ ESR tantalum capacitor) will be sufficient
to provide adequate ripple voltage at the input of the
module. To minimize the ripple voltage at the input,
very low ESR ceramic capacitors are recommended at
the input of the module. Figure 26 shows input ripple
voltage (mVp-p) for various outputs with 4x47 µF
tantalum capacitors and with 4x 22 µF ceramic
capacitor (TDK part #: C4532X5R1C226M) at full load.
Figure 26. Input ripple voltage for various output
with 4x47 µF polymer and 4x22 µF ceramic
capacitors at the input (full load).
300
200
250
1 00
150
50
0
0
1
Output Voltage (Vdc)
2
3
4
Tantalum
Ceramic
5
10
6