DS1200-3-002 Emerson Network Power, DS1200-3-002 Datasheet - Page 29

• Manufacturer Part Number: DS1200-3-002
• Description: POWER SUPPLY AC/DC 12V 1200W
• Manufacturer: Emerson Network Power
• Series: DS1200r

Specifications of DS1200-3-002

• Voltage - Output: 12V
• Number Of Outputs: 1
• Power (watts): 1200W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 180 ~ 264VAC
• Mounting Type: Chassis Mount
• 1st Output: 12 VDC @ 100A
• Size / Dimension: 11" L x 3.2" W x 1.57" H (279.4mm x 81.3mm x 39.9mm)
• Power (watts) - Rated: 1200W
• Operating Temperature: -10°C ~ 50°C
• Efficiency: 91%
• Approvals: CB, CE, cUL, EN, NEMKO, UL
• Line Regulation: ±5%
• Load Regulation: ±5%
• Input Voltage: 90 to 264V
• Output Voltage: 12V
• Input Frequency: 47 to 63Hz
• Screening Level: Commercial
• Operating Temperature Min Deg. C: -10C
• Operating Temperature Max Deg. C: 50C
• Mounting Style: Desktop
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 454-1271

I
The DS1200-3 power supply contains enhanced monitoring and control functions implemented via the I
DS1200-3 I
communication bus is powered either by the internal 3.3V supply or from an external power source connected to the
StandBy Output (ie: accessing an unpowered power supply as long as the StandBy Output of another power supply
connected in parallel is on).
If units are connected in parallel or in redundant mode, the StandBy Outputs must be connected together in the system.
Otherwise, the I
Note:
SDA, SCL (I
I
must be pulled-up in the system by an 1K ohm resistor to the StandBy Output.
S_INT (Alarm) – (pin D3)
S_INT is used to send a signal to the system that a fault in the power supply occurred. This signal is normally logic level
HIGH. It will go to a LOW logic level when a fault bit has been set in the power supply’s status register. To reset the
S_INT signal back to normal (logic HIGH level), perform one of the following actions - (1) recycle input AC power, (2)
toggle PSON signal and (3) issuance of a CLEAR_FAULTS PMBus
A0, A1 (I
These two input pins are the address lines A0 and A1 to indicate the slot position the power supply occupies in the power
bay and define the power supply addresses for FRU data and PMBus
assign different addresses for each power supply. During I
system will be the master and power supplies will be slave.
They are internally pulled up to internal 3.3V supply with a 1K resistor.
I
The interval between two consecutive I
monitoring functionality.
I
The noise on the I
measurement should be made with an oscilloscope bandwidth limited to 100MHz. Measurements should be make at the
power supply output connector with 3.2K ohm resistors pulled up to StandBy Output and 20pf ceramic capacitors to
StandBy Output Return.
The noise on the address lines A0 and A1 will be less than 100mV peak-to-peak. This noise measurement should be
made at the power supply output connector.
2
2
2
2
C serial data and clock bus - these pins are internally pulled up to internal 3.3V supply with a 39K resistor. These pins
C Bus Communication Interval
C Bus Signal Integrity
C Bus Signals
PMBus
Guaranteed communication I
2
C Address BIT 0, BIT1 Signals) – (pin D1, D2)
2
C functionality (PMBus
2
C Data and Clock Signals) – (pin C1, C2)
TM
2
C bus will not work properly when a unit is inserted into the system without the AC source connected.
2
functionality can be accessed only when the PSU is powered-up.
C bus (SDA, SCL lines) due to the power supply will be less than 500mV peak-to-peak. This noise
TM
2
and FRU data) can be accessed via the output connector control signals. The
C speed is 100KHz.
2
C communications to the power supply should be at least 50ms to ensure proper
2
C communication between system and power supplies, the
TM
TM
command.
data communication. This allows the system to
2
C bus. The
Rev.10.03.30_#0.1
DS1200-3 Series
Page 29