DM-COP8/44P National Semiconductor, DM-COP8/44P Datasheet - Page 197
DM-COP8/44P
Manufacturer Part Number
DM-COP8/44P
Description
CABLE FOR DEBUG MODULE 44-PLCC
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of DM-COP8/44P
Accessory Type
44-PLCC Target Cable
For Use With/related Products
MetaLink Debug Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DM-COP8/44P
- Current page: 197 of 254
- Download datasheet (2Mb)
4.2.2
This example shows the COP8SAx7 interface to a NM93C06, a 256-bit E
the MICROWIRE/PLUS interface. The pin connections for the interface is shown in
Figure 4-4. Some notes on the NM93C06 interface requirements are:
1. Set the MSEL bit in the CNTRL register to enable MICROWIRE; G0 and G5
2. Normal mode of operation until interrupted by CS going low.
3. Set the BUSY flag and load SIOR register with the data to be sent out on S0.
4. Wait for the BUSY flag to be reset. (The BUSY flag automatically resets after
5. If data is being read in, the contents of the SIO register are saved.
6. The prearranged set of data transfers are performed.
7. Repeat steps 3 through 6. The user must ensure step 3 is performed within t-
1. The SK clock frequency should be less than 250 KHz. The SK clock should be
NM93C06-COP8SAx7 Interface
are configured as inputs and G4 as an output. Reset bit 6 of the Port G con-
figuration register to select Standard SK Clocking mode.
(The shift register shifts eight bits of data from S0 at the high-order end of
the shift register. Concurrently, eight new bits of data from SI are loaded into
the low-order end of the shift register.)
8 bits of data have been shifted.)
time (refer to Figure 4-3) as agreed upon in the protocol.
configured for standard SK mode.
CKI
CKO
COP8SAx7
Figure 4-4 NM93C06-COP8SAx7 Interface
V
CC
GND
GO
SO
SK
SI
DI
DO
SK
CS
COP8SAx7 APPLICATION IDEAS
NM93C06
GND
2
PROM, using
V
CC
4-5
Related parts for DM-COP8/44P
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CABLE FOR DEBUG MODULE 20-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
CABLE FOR DEBUG MODULE 28-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 10A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH PWR ROCKER DPST SNAP-IN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER SPST ILUM 10A/125V
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT W/MRK QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER ILLUM 10A GRN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
MINI ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER SPST 3A QC
Manufacturer:
C&K Components
Datasheet: