KSZ8851SNL-BBE-EVAL Micrel Inc, KSZ8851SNL-BBE-EVAL Datasheet - Page 56

• Manufacturer Part Number: KSZ8851SNL-BBE-EVAL
• Description: BOARD EVAL MAC/PHY FOR KSZ8851
• Manufacturer: Micrel Inc
• Series: LinkMD®r

Specifications of KSZ8851SNL-BBE-EVAL

• Design Resources: BeagleBoard Zippy2
• Main Purpose: Interface, Ethernet Controller (PHY and MAC)
• Embedded: No
• Utilized Ic / Part: KSZ8851SNL
• Primary Attributes: 1 Port, 100BASE-TX/10BASE-T
• Secondary Attributes: SPI Interface, LinkMD Cable Diagnostics
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-3602; KSZ8851SNL-BBE-EVL; ZIPPY2

Interrupt Status Register (0x92 – 0x93): ISR
This register contains the status bits for all QMU and other interrupt sources.
When the corresponding enable bit is set, it causes the interrupt pin to be asserted.
This register is usually read by the host CPU and device drivers during interrupt service routine or polling. The register
bits are not cleared when read. The user has to write “1” to clear.
August 2009
Micrel, Inc.
Bit
4
3
2
1
0
Bit
15
14
13
12
11
10
9
8
7
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x1
0x1
0x0
Default Value
Default Value
R/W
RW
RW
RW
RW
RW
R/W
RO
(W1C)
RO
(W1C)
RO
(W1C)
RO
RO
(W1C)
RO
RO
(W1C)
RO
(W1C)
RO
Description
RXMPDIE Receive Magic Packet Detect Interrupt Enable
When this bit is set, the Receive magic packet detect interrupt is enabled.
When this bit is reset, the Receive magic packet detect interrupt is disabled.
LDIE Linkup Detect Interrupt Enable
When this bit is set, the wake-up from linkup detect interrupt is enabled.
When this bit is reset, the linkup detect interrupt is disabled.
EDIE Energy Detect Interrupt Enable
When this bit is set, the wake-up from energy detect interrupt is enabled.
When this bit is reset, the energy detect interrupt is disabled.
SPIBEIE SPI Bus Error Interrupt Enable
When this bit is set, the SPI bus error interrupt is enabled.
When this bit is reset, the SPI bus error interrupt is disabled.
DEDIE Delay Energy Detect Interrupt Enable
When this bit is set, the delay energy detect interrupt is enabled.
When this bit is reset, the delay energy detect interrupt is disabled.
Note: the delay energy detect interrupt till device is ready for host access.
Description
LCIS Link Change Interrupt Status
When this bit is set, it indicates that the link status has changed from link up to link down,
or link down to link up.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
TXIS Transmit Interrupt Status
When this bit is set, it indicates that the TXQ MAC has transmitted at least a frame on the
MAC interface and the QMU TXQ is ready for new frames from the host.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
RXIS Receive Interrupt Status
When this bit is set, it indicates that the QMU RXQ has received at least a frame from the
MAC interface and the frame is ready for the host CPU to process.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
RXOIS Receive Overrun Interrupt Status
When this bit is set, it indicates that the Receive Overrun status has occurred.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
TXPSIS Transmit Process Stopped Interrupt Status
When this bit is set, it indicates that the Transmit Process has stopped.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
RXPSIS Receive Process Stopped Interrupt Status
When this bit is set, it indicates that the Receive Process has stopped.
This edge-triggered interrupt status is cleared by writing 1 to this bit.
Reserved
56
KSZ8851SNL/SNLI
M9999-083109-2.0