CY3276 Cypress Semiconductor Corp, CY3276 Datasheet - Page 11
![DEV PROG POWERLINE HIGH EZCOLOR](/photos/9/6/90661/cy3276_sml.jpg)
CY3276
Manufacturer Part Number
CY3276
Description
DEV PROG POWERLINE HIGH EZCOLOR
Manufacturer
Cypress Semiconductor Corp
Type
Other Power Managementr
Datasheet
1.CY3276.pdf
(36 pages)
Specifications of CY3276
Mfg Application Notes
Powerline Comm Brd Design AppNote
Main Purpose
Interface, Transceiver, Powerline Communication
Embedded
No
Utilized Ic / Part
CY8CLED16P01
Primary Attributes
2400bps Data Transfer Over High Voltage Power Lines
Secondary Attributes
User Configurable LEDs
Board Size
127 mm x 101.6 mm
Interface Type
RS-232, Ethernet, I2C, ISSP
Maximum Operating Temperature
+ 40 C
Operating Supply Voltage
110 V to 240 V
Product
Power Management Development Tools
Dimensions
127 mm x 101.6 mm
Silicon Manufacturer
Cypress
Silicon Core Number
CY8CLED16P01
Kit Application Type
Communication & Networking
For Use With/related Products
CY8CLED16P01
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
428-3004
2.3.1
2.3.2
2.3.3
CY3276 Cypress High Voltage Programmable PLC Development Kit Guide, Doc. # 001-55116 Rev. *B
■
■
High Voltage Section with SMPS
This section gets power from the powerline and generates necessary low DC voltage for the opera-
tion of the PLC transceiver and other components on the chip.
Table 2-1. Key High Voltage with SMPS Components
Transmit Amplifier and Filtering Section
This section takes the output signal from the transceiver chip. The circuit amplifies the signal and fil-
ters it for compliance purposes only. The amplification is to drive the signal on long cables or in low
impedance networks. Filtering is done in three stages.
Table 2-2. Key Transmit Amplifier and Filtering Components
Transmit and Receive Coupling Circuit
This circuit couples the signal from the board on to the powerline. On the receive side, the same cir-
cuit couples the carrier on the powerline into the board rejecting the actual 50 and 60 Hz powerline
signal. The isolation transformer in the circuit is required for safety.
Table 2-3. Key Transmit and Receive Components
J7
F1
D7
T3
U6
T2
U5
U2, U3
U4, Q1, Q2
T1
C9
Component
Component
Component
Daughter Card
RJ45 Connector for Debugging
This is the two pin connector where the AC cable hooks up to the powerline.
Protection fuse for the circuit.
Full wave bridge rectifier diode IC.
Common mode choke.
iW1690-07 – iWatt high performance AC/DC power supply controller.
Flyback transformer.
5V regulator.
These opamps are used to filter the signal from the CY8CLED16P01 removing the harmon-
ics. The filter stages are only required to meet the European CENELEC EN50065-1:2001
signaling specification. They are not required to achieve robust PLC communication.
These opamp and high gain transistors are used for the power amplification stage.
This is the isolation transformer which provides isolation between the HV and LV sections of
the board. It is 1:1 ratio transformer.
This is the coupling capacitor which couples the communication signal and rejects the low
frequency noise. The voltage and X1 safety rating of this component are important parame-
ters.
Description
Description
Description
PLC Development Board
11
[+] Feedback