EVB-USB2512Q36-BAS SMSC, EVB-USB2512Q36-BAS Datasheet - Page 38
![BOARD EVAL FOR USB2512/USB2512I](/photos/9/10/91014/evb-usb2512q36-bas_sml.jpg)
EVB-USB2512Q36-BAS
Manufacturer Part Number
EVB-USB2512Q36-BAS
Description
BOARD EVAL FOR USB2512/USB2512I
Manufacturer
SMSC
Specifications of EVB-USB2512Q36-BAS
Main Purpose
Interface, USB 2.0 Hub
Embedded
No
Utilized Ic / Part
USB2512, USB2512I
Primary Attributes
Dual Port Hub, High Speed (480Mbps), I2C/SMBus
Secondary Attributes
Overcurrent Protection, Port Power Switching, ESD Protection
Interface Type
USB
Operating Supply Voltage
5 V
Product
Interface Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
USB2512
Other names
638-1041
EVB-USB2512Q36-BAS (USB2512/USB2512I)
EVB-USB2512Q36-BAS (USB2512/USB2512I)
Revision 1.1 (04-26-10)
8.2.1.7
NUMBER
BIT
7
6
5
4
3
Register 06h: CONFIG_BYTE_1
SELF_BUS_PWR
EOP_DISABLE
MTT_ENABLE
HS_DISABLE
BIT NAME
Reserved
Self or Bus Power: Selects between Self- and Bus-Powered operation.
The hub is either self-powered (draws less than 2 mA of upstream bus
power) or bus-powered (limited to a 100 mA maximum of upstream power
prior to being configured by the host controller).
When configured as a bus-powered device, the SMSC hub consumes less
than 100 mA of current prior to being configured. After configuration, the bus-
powered SMSC hub (along with all associated hub circuitry, any embedded
devices if part of a compound device, and 100 mA per externally available
downstream port) must consume no more than 500 mA of upstream VBUS
current. The current consumption is system dependent, and the OEM must
ensure that the USB 2.0 specifications are not violated.
When configured as a self-powered device, <1 mA of upstream VBUS
current is consumed and all ports are available, with each port being capable
of sourcing 500 mA of current.
This field is set by the OEM using either the SMBus or EEPROM interface
options.
Please see the description under dynamic power for the self-/bus- power
functionality when dynamic power switching is enabled.
'0' = Bus-powered operation
’1’ = Self-powered operation
If dynamic power switching is enabled, this bit is ignored and the
LOCAL_PWR pin is used to determine if the hub is operating from self or
bus power.
Reserved
Hi-speed Disable: Disables the capability to attach as either a Hi-/Full-Speed
device, and forces attachment as Full-Speed only (i.e. no Hi-Speed support).
'0' = Hi-/Full-speed
‘1’ = Full-speed-Only (Hi-speed disabled!)
Multi-TT enable: Enables one transaction translator per port operation.
(Not available on the USB2512A/12Ai.)
Selects between a mode where only one transaction translator is available
for all ports (Single-TT), or each port gets a dedicated transaction translator
(Multi-TT).
'0' = Single TT for all ports
‘1’ = One TT per port (when multiple TT's are supported)
EOP Disable: Disables EOP generation at EOF1 when in Full-Speed mode.
During FS operation only, this permits the hub to send EOP if no
downstream traffic is detected at EOF1. See Section 11.3.1 of the USB 2.0
specification for additional details.
'0' = EOP generation is normal
‘1’ = EOP generation is disabled
DATASHEET
38
DESCRIPTION
USB 2.0 Hi-Speed Hub Controller
SMSC USB251x
Datasheet