DEMO9S08LL16 Freescale Semiconductor, DEMO9S08LL16 Datasheet - Page 14

• Manufacturer Part Number: DEMO9S08LL16
• Description: BOARD DEMO FOR MC9S08LL16 MCU
• Manufacturer: Freescale Semiconductor
• Series: HCS08r
• Type: MCUr

Specifications of DEMO9S08LL16

• Contents: Board, Cable, DVD
• Silicon Manufacturer: Freescale
• Core Architecture: HCS08
• Core Sub-architecture: HCS08
• Silicon Core Number: MC9S08
• Silicon Family Name: S08LL
• Kit Contents: Board
• Rohs Compliant: Yes
• For Use With/related Products: MC9S08LL16
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

1
2
3
4
5
6
7
8
Num C
Electrical Characteristics
12
13
14
15
16
17
18
19
20
21
22
23
14
Typical values are measured at 25 C. Characterized, not tested
All I/O pins except for LCD pins in open drain mode.
Total leakage current is the sum value for all GPIO pins. This leakage current is not distributed evenly across all pins but
characterization data shows that individual pin leakage current maximums are less than 250 nA.
All functional non-supply pins, except for PTB2 are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
Power supply must maintain regulation within operating V
conditions. If the positive injection current (V
result in external power supply going out of regulation. Ensure that external V
injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is
present, or if clock rate is very low (which would reduce overall power consumption).
POR will occur below the minimum voltage.
Factory trimmed at V
P
P
P Pullup,
P
D
C Input capacitance, all pins
C RAM retention voltage
C POR re-arm voltage
D POR re-arm time
P Low-voltage detection threshold
P Low-voltage warning threshold
P Low-voltage inhibit reset/recover hysteresis
P Bandgap voltage reference
Hi-Z (off-state)
leakage
current
Total leakage
current
pulldown
resistors when
enabled
DC injection
current
3
4, 5, 6
DD
Characteristic
= 3.0 V, Temp = 25 C.
Total leakage current for all
Single pin limit
Total MCU limit, includes
sum of all stressed pins
7
PTA[4:5], PTD[0:7],
PTB[0:7], PTC[0:7]
PTA[0:3], PTA[6:7],
8
all input/output
Table 8. DC Characteristics (continued)
MC9S08LL16 Series MCU Data Sheet, Rev. 6
PTE[0:7]
(per pin)
In
> V
pins
DD
) is greater than I
Symbol
V
V
V
V
R
t
|I
|I
V
R
V
POR
C
I
RAM
POR
LVW
OZ
InT
LVD
PU,
IC
hys
PD
BG
In
DD
|
|
range during instantaneous and operating maximum current
V
IN
V
V
In
In
< V
Condition
= V
= V
DD
SS
DD
DD
—
, the injection current may flow out of V
, V
V
V
V
V
SS
DD
DD
or V
or V
IN
DD
DD
and V
DD
> V
falling
falling
rising
rising
SS
SS
load will shunt current greater than maximum
DD
DD
.
17.5
–0.2
1.80
1.88
2.08
1.15
Min
0.9
–5
10
—
—
—
—
—
0.025
Typ
1.84
1.92
2.14
1.17
0.6
1.4
80
—
—
—
—
—
—
Freescale Semiconductor
1
Max
52.5
69.5
1.88
1.96
1.18
DD
0.2
1.0
2.0
2.2
—
—
1
2
5
8
and could
Unit
mA
mA
mV
A
A
k
pF
s
V
V
V
V
V