C8051F996DK Silicon Laboratories Inc, C8051F996DK Datasheet - Page 241
![KIT DEV FOR C8051F996](/photos/28/41/284142/c8051f996dk_sml.jpg)
C8051F996DK
Manufacturer Part Number
C8051F996DK
Description
KIT DEV FOR C8051F996
Manufacturer
Silicon Laboratories Inc
Type
MCUr
Datasheets
1.C8051F996DK.pdf
(24 pages)
2.C8051F996DK.pdf
(2 pages)
3.C8051F996DK.pdf
(4 pages)
4.C8051F996DK.pdf
(322 pages)
Specifications of C8051F996DK
Contents
Board, Batteries, Cables, CDs, Debug Adapter, Documentation, Power Adapter
Processor To Be Evaluated
C8051F996
Processor Series
C8051F98x
Interface Type
USB
Operating Supply Voltage
3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
C8051F996
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1963
- C8051F996DK PDF datasheet
- C8051F996DK PDF datasheet #2
- C8051F996DK PDF datasheet #3
- C8051F996DK PDF datasheet #4
- Current page: 241 of 322
- Download datasheet (3Mb)
C8051F99x-C8051F98x
22.4.2. SMB0CN Control Register
SMB0CN is used to control the interface and to provide status information (see SFR Definition 22.2). The
higher four bits of SMB0CN (MASTER, TXMODE, STA, and STO) form a status vector that can be used to
jump to service routines. MASTER indicates whether a device is the master or slave during the current
transfer. TXMODE indicates whether the device is transmitting or receiving data for the current byte.
STA and STO indicate that a START and/or STOP has been detected or generated since the last SMBus
interrupt. STA and STO are also used to generate START and STOP conditions when operating as a mas-
ter. Writing a 1 to STA will cause the SMBus interface to enter Master Mode and generate a START when
the bus becomes free (STA is not cleared by hardware after the START is generated). Writing a 1 to STO
while in Master Mode will cause the interface to generate a STOP and end the current transfer after the
next ACK cycle. If STO and STA are both set (while in Master Mode), a STOP followed by a START will be
generated.
The ARBLOST bit indicates that the interface has lost an arbitration. This may occur anytime the interface
is transmitting (master or slave). A lost arbitration while operating as a slave indicates a bus error condi-
tion. ARBLOST is cleared by hardware each time SI is cleared.
The SI bit (SMBus Interrupt Flag) is set at the beginning and end of each transfer, after each byte frame, or
when an arbitration is lost; see Table 22.3 for more details.
Important Note About the SI Bit: The SMBus interface is stalled while SI is set; thus SCL is held low, and
the bus is stalled until software clears SI.
22.4.2.1.Software ACK Generation
When the EHACK bit in register SMB0ADM is cleared to 0, the firmware on the device must detect incom-
ing slave addresses and ACK or NACK the slave address and incoming data bytes. As a receiver, writing
the ACK bit defines the outgoing ACK value; as a transmitter, reading the ACK bit indicates the value
received during the last ACK cycle. ACKRQ is set each time a byte is received, indicating that an outgoing
ACK value is needed. When ACKRQ is set, software should write the desired outgoing value to the ACK
bit before clearing SI. A NACK will be generated if software does not write the ACK bit before clearing SI.
SDA will reflect the defined ACK value immediately following a write to the ACK bit; however SCL will
remain low until SI is cleared. If a received slave address is not acknowledged, further slave events will be
ignored until the next START is detected.
22.4.2.2.Hardware ACK Generation
When the EHACK bit in register SMB0ADM is set to 1, automatic slave address recognition and ACK gen-
eration is enabled. More detail about automatic slave address recognition can be found in Section 22.4.3.
As a receiver, the value currently specified by the ACK bit will be automatically sent on the bus during the
ACK cycle of an incoming data byte. As a transmitter, reading the ACK bit indicates the value received on
the last ACK cycle. The ACKRQ bit is not used when hardware ACK generation is enabled. If a received
slave address is NACKed by hardware, further slave events will be ignored until the next START is
detected, and no interrupt will be generated.
Table 22.3 lists all sources for hardware changes to the SMB0CN bits. Refer to Table 22.5 for SMBus sta-
tus decoding using the SMB0CN register.
Rev. 1.0
241
Related parts for C8051F996DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![500SAAB8M00000ACF](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
SMD/C°/SINGLE-ENDED OUTPUT SILICON OSCILLATOR
Manufacturer:
Silicon Laboratories Inc
![SI3210MFT](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DAAKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 AES KEYFOB DEMO WITH LCD RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DASKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 SIMPLIFIED KEY FOB DEMO WITH LED RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4432-SEB1 C 915](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A/-40 TO 85 OC/EZLINK MODULE; F930/4432 HIGH BAND (REV E/B1)
Manufacturer:
Silicon Laboratories Inc
![4432-SEB1 D 470](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
EZLink Module; F930/4432 Low Band (rev e/B1)
Manufacturer:
Silicon Laboratories Inc
![4460-TCE10D434-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4460 10 DBM RADIO TEST CARD 434 MHZ
Manufacturer:
Silicon Laboratories Inc
![4461-TSQ14D868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4461 14 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C460-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RFSWITCH RADIO TEST CARD 460 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE27F868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 27 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915S-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 SKYWORKS 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915R-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/-40 TO 85 OC/4463 RFMD 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TSQ20D169-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 169 MHZ
Manufacturer:
Silicon Laboratories Inc