101-1017 Rabbit Semiconductor, 101-1017 Datasheet - Page 111
101-1017
Manufacturer Part Number
101-1017
Description
KIT DEV POWERCORE 3800 INT'L
Manufacturer
Rabbit Semiconductor
Series
PowerCore FLEXr
Type
MPU Moduler
Datasheet
1.101-1007.pdf
(240 pages)
Specifications of 101-1017
Contents
RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
Processor To Be Evaluated
PowerCore 38xx
Interface Type
Ethernet
For Use With/related Products
RCM3800
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 111 of 240
- Download datasheet (3Mb)
•
6.7 Where Do I Go From Here?
If there are any problems at this point:
• Use the Dynamic C
• Check the Rabbit Semiconductor Technical Bulletin Board at
• Use the Technical Support e-mail form at www.rabbit.com/support/.
If the sample programs ran fine, you are now ready to go on.
Additional sample programs are described in the Dynamic C TCP/IP User’s Manual.
Please refer to the Dynamic C TCP/IP User’s Manual to develop your own applications.
An Introduction to TCP/IP provides background information on TCP/IP, and is available
on the CD and on our
User’s Manual
TELNET.c
out Serial Port E. It uses a digital input to indicate that the TCP/IP connection should be
closed and a digital output to toggle an LED to indicate that there is an active connection.
PC Setup
Connect PC to PowerCore Prototyping Board
Once you have compiled and run the sample program, start a Telnet session on your PC
(
TCPCONFIG 1
otherwise use the TCP/IP settings you entered in the
Now look at LED DS5 on the Prototyping Board—a blinking LED indicates that there
is an active Telnet connection. You can type a message in the Telnet window, then view
the message using a PC serial utility such as Tera Term. Press switch S2 on the Proto-
typing Board to close the Telnet connection; DS5 should stop blinking, indicating that
the Telnet connection has been closed.
www.rabbit.com/support/bb/.
Start > Run telnet 10.10.6.100
1. Start up a PC serial utility such as Tera Term or Hyperterminal.
2. Configure the serial parameters for a baud rate of 19200, 8 bits, no parity and 1 stop bit.
3. Enable the “Local Echo” option.
4. Enable the option to append linefeeds to incoming and outgoing messages.
1. Connect PC Tx to pin 4 on header J1 of the Prototyping Board (RXF).
2. Connect PC Rx to pin 6 on header J1 of the Prototyping Board (TXF).
3. Connect PC GND to pin 9 on header J1 of the Prototyping Board (GND).
NOTE: If you purchased your PowerCore module through a distributor or through a
Rabbit Semiconductor partner, contact the distributor or partner first for technical
support.
—This sample program takes anything that comes in on a port and sends it
macro in the sample program, the IP address is 10.10.6.100 as shown;
Web
Help
site.
menu to get further assistance with Dynamic C.
). As long as you have not modified the
TCP_CONFIG.LIB
library.
103
Related parts for 101-1017
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV STANDARD RCM5700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories Keypad/Display Unit 5V Panel Mount
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
Single Board Computers 24VDC/110 Power Supp
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor