EPSILON5-A1 Equinox Technologies, EPSILON5-A1 Datasheet - Page 17

• Manufacturer Part Number: EPSILON5-A1
• Description: ISP PORTABLE PROGRAMMER USB
• Manufacturer: Equinox Technologies
• Series: Epsilon5r
• Type: Portable ISPr

Specifications of EPSILON5-A1

• Contents: Programmer, Software, Cables and Documentation
• Ic Product Type: In-Circuit Programmer
• Features: 2Mbits Of On-Board Non-Volatile FLASH Memory For User Project Storage
• Interface Type: JTAG
• Mcu Supported Families: ATmega And AT91SAM7
• Mpu Supported Families: AVR
• Rohs Compliant: Yes
• External Depth: 31mm
• Height: 189mm
• Length: 80mm
• For Use With/related Products: ATMEL AT89S, AVR, AT91SAM7, NXP P89C51Rx2 P89C66x, Zensys, Serial EEPROM's
• Other names: 483-1000

9
10 PC requirements
11 Power Supply
12 Voltage range
13 Vpp Voltage
14 DC Power Connector
15 Programmer Current
16 Max. current through
17 Target SPI Speed
18 Target UART Speed
19 ISP Headers
20 Frequency generator
21 PC Connection (J5)
6
PC Control Software The programmer can be controlled using:
Options
Generator
(CON1)
Consumption
programmer
output (SCK2)
i.
ii.
iii.
iv.
v.
PC running Windows 95 / 98 / 2000 or ME / NT4 / XP
There are 3 possible modes for powering the Programmer /
Target System:
i.
ii.
iii.
See specified section
On Board +12.0V Vpp Voltage Generator
(Applies +12.0V to RESET pin for ATtiny HV programming)
This refers to the current consumption of the actual
programmer circuitry. See specified section.
This refers to the maximum current which can be supplied
through the programmer from CON1 (i.e. external power
supply) to the Target System.
Max current = 300 mA.
SLOW SPI: 0 – 490.2 kHz (user selectable)
FAST SPI: Disabled
( SPI speeds are estimations only due to uneven mark/space
ratio and non-continuous waveforms)
This is the Communications Speed (BAUD rate) from the
programmer to the Target Device when communicating via a
Boot Loader. The BAUD rate is configurable from 1,200 to 115
kBaud. This settings is completely independent from the BAUD
rate settings for the PC communicating with the programmer.
4 x ISP Headers (inside enclosure)
Programmer can output a configurable square wave frequency
on the SCK2 pin. This is used to clock the Target Device in the
absence of a Target Oscillator.
•
•
•
i.
ii.
iii.
iv.
•
EQTools (as standard)
ISP-PRO (chargeable upgrade)
Standalone Upload Wizard (chargeable upgrade)
ConsoleEDS (chargeable upgrade)
ASCII Text Mode (chargeable upgrade)
Programmer powers Target System
Target System powers the Programmer
Programmer and Target System are independently
powered
DC Power Connector
2.5 mm Jack Socket – Centre Positive
DC Power Lead supplied with programmer – white
stripe is +ve.
RS232 9-way Female D Connector
Atmel 10-way (JTAG)
Equinox 10-way (SPI+UART)
Atmel 10-way (SPI)
Atmel 6-way (SPI)
EPSILON5 MKII Programmer - User Guide V1.10 – 10th July 2006
2.3
2.3
3.0
1.5.2
1.5.2
1.5.3
1.5.3
4.0
1.5.6