HDJD-JD05 Avago Technologies US Inc., HDJD-JD05 Datasheet
![KIT DEV RGB COLOR SENSOR 20-QFN](/photos/26/97/269780/hdjd-jd05_wht_sml.jpg)
HDJD-JD05
Specifications of HDJD-JD05
Related parts for HDJD-JD05
HDJD-JD05 Summary of contents
Page 1
ADJD-S313-QR999 Miniature Surface-Mount RGB Digital Color Sensor Data Sheet Description The ADJD-S313-QR999 is a cost effective, CMOS digital output RGB color sensor in miniature surface-mount package with a mere size of 5x5x0.75mm. The IC comes with integrated RGB filters, an ...
Page 2
Powering the Device No voltage must be applied to IO's during power-up and power-down ramp time V DDD / V DDA 0V t VDD_RAMP ESD Protection Diode Turn-On During Power-Up and Power-Down A particular power-up and power-down sequence must be ...
Page 3
Electrical Specifications Absolute Maximum Ratings (Notes 1 & 2) Parameter Storage temperature Digital supply voltage, DVDD to DVSS Analog supply voltage, AVDD to AVSS Input voltage Solder Reflow Peak temperature Human Body Model ESD rating Recommended Operating Conditions Parameter Free ...
Page 4
Optical Specification Parameter Dark offset* *code is from dark code to (dark code + 128LSB) Minimum sensitivity Parameter Symbol Irradiance Responsivity Re Maximum sensitivity Parameter Symbol Irradiance Responsivity Re Minimum sensitivity Parameter Symbol Saturation Irradiance (note 13) Maximum sensitivity Parameter ...
Page 5
Notes: 1. The “Absolute Maximum Ratings” are those values beyond which damage to the device may occur. The device should not be operated at these limits. The parametric values defined in the “Electrical Specifications” table are not guaranteed at the ...
Page 6
High Level Description The sensor needs to be configured before it can be used. The gain selection needs to be set for optimum performance depending on light levels. The flowcharts below describe the different procedures required. SENSOR GAIN OPTIMIZATION Step ...
Page 7
Detail Description A hardware reset (by asserting XRST) should be performed before starting any operation. The user controls and configures the device by programming a set of internal registers through a serial interface. At the start of application, the following ...
Page 8
Serial Interface Reference Description The programming interface to the ADJD-S313 is a 2-wire serial bus. The bus consists of a serial clock (SCL) and a serial data (SDA) line. The SDA line is bi-directional on ADJD-S313 and must be connected ...
Page 9
The SCL clock line synchronizes the serial data transmission on the SDA data line always generated by the master. The frequency of the SCL clock line may vary throughout the transmission as long as it still meets the ...
Page 10
In the case of the master-receiver and slave- transmitter, the master generates acknowledge to signal the end of the data transfer to the slave-transmitter. The master can then send a STOP or repeated START condition to begin a new data ...
Page 11
Data format ADJD-S313 uses a register-based programming architecture. Each register has a unique address and controls a specific function inside the chip. To write to a register, the master first generates a START condition. Then it sends the slave address ...
Page 12
Powering the Device Ground Connection AGND and DGND must both be set to 0V and preferably star-connected to a central power source as shown in the application diagram. A potential difference between AGND and DGND may cause the ESD diodes ...
Page 13
Package Dimensions Bottom View NOTE: DIMENSIONS ARE IN MILIMETERS (MM) 13 ...
Page 14
Recommended Reflow Profile It is recommended that Henkel Pb-free solder paste LF310 be used for soldering ADJD-S313. Below is the recommended soldering profile. 230 ± 5˚C/sec. T-peak 218 ˚C/sec. T-reflow DELTA-FLUX = 2 ˚C/sec. max. 160 ˚C T-max. 120˚C T-min. ...
Page 15
Recommendations for Handling and Storage of ADJD-S313 Before Opening the MBB (Moisture Barrier Bag) • The sensor component must be kept sealed in a MBB (Moisture Barrier Bag) stored at 30°C and 70%RH or less at all times. • It ...
Page 16
Reel Dimensions R10.65 R5.2 45 EMBOSSED RIBS RAISED: 0.25 mm WIDTH: 1.25 mm NOTES: 1. *MEASURED AT HUB AREA. 2. ALL FLANGE EDGES TO BE ROUNDED. For product information and a complete list of distributors, please go to our web ...