PPC8544EVTANG Freescale Semiconductor, PPC8544EVTANG Datasheet - Page 64
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
PPC8544EVTANG
Manufacturer Part Number
PPC8544EVTANG
Description
EVAL MPC8544 783FCPBGA
Manufacturer
Freescale Semiconductor
Type
Microcontrollerr
Datasheet
1.MPC8544VTALF.pdf
(117 pages)
Specifications of PPC8544EVTANG
Contents
Board
For Use With/related Products
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PPC8544EVTANG
Manufacturer:
FREESCALE
Quantity:
20 000
High-Speed Serial Interfaces (HSSI)
Using this waveform, the definitions are as follows. To simplify illustration, the following definitions
assume that the SerDes transmitter and receiver operate in a fully symmetrical differential signaling
environment.
64
1. Single-Ended Swing
2. Differential Output Voltage, V
3. Differential Input Voltage, V
4. Differential Peak Voltage, V
5. Differential Peak-to-Peak, V
6. Differential Waveform
7. Common Mode Voltage, V
the two complimentary output voltages: V
or negative.
The Differential Output Voltage (or Swing) of the transmitter, V
SDn_RX each have a peak-to-peak swing of A - B Volts. This is also referred as each signal wire’s
Single-Ended Swing.
two complimentary input voltages: V
negative.
each range from A – B to –(A – B) Volts, the peak-to-peak value of the differential transmitter
output signal or the differential receiver input signal is defined as Differential Peak-to-Peak
Voltage, V
amplitude, or twice of the differential peak. For example, the output differential peak-peak voltage
can also be calculated as V
of a balanced interchange circuit and ground. In this example, for SerDes output, V
V
voltages within a differential pair. In a system, the common mode voltage may often differ from
one component’s output to the other’s input. Sometimes, it may be even different between the
receiver input and driver output circuits within the same component. It is also referred as the DC
offset in some occasions.
The transmitter output signals and the receiver input signals SDn_TX, SDn_TX, SDn_RX and
The Differential Input Voltage (or Swing) of the receiver, V
The peak value of the differential transmitter output signal or the differential receiver input signal
Since the differential output signal of the transmitter and the differential input signal of the receiver
The differential waveform is constructed by subtracting the inverting signal (SDn_TX, for
The Common Mode Voltage is equal to one half of the sum of the voltages between each conductor
is defined as Differential Peak Voltage, V
example) from the non-inverting signal (SDn_TX, for example) within a differential pair. There is
only one signal trace curve in a differential waveform. The voltage represented in the differential
waveform is not referenced to ground. Refer to
SDn_TX
MPC8544E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
+ V
DIFFp-p
SDn_TX
= 2*V
= (A + B) / 2, which is the arithmetic mean of the two complimentary output
DIFFp
TX-DIFFp-p
cm
DIFFp
= 2 * |(A – B)| Volts, which is twice of differential swing in
DIFFp-p
ID
OD
(or Differential Input Swing):
(or Differential Output Swing):
SDn_RX
= 2*|V
SDn_TX
DIFFp
OD
– V
Figure 44
= |A – B| Volts.
|.
SDn_RX.
– V
SDn_TX.
The V
as an example for differential waveform.
ID
The V
, is defined as the difference of the
ID
OD
value can be either positive or
, is defined as the difference of
OD
value can be either positive
Freescale Semiconductor
cm_out
=