PPC8544EVTANG Freescale Semiconductor, PPC8544EVTANG Datasheet - Page 79
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
PPC8544EVTANG
Manufacturer Part Number
PPC8544EVTANG
Description
EVAL MPC8544 783FCPBGA
Manufacturer
Freescale Semiconductor
Type
Microcontrollerr
Datasheet
1.MPC8544VTALF.pdf
(117 pages)
Specifications of PPC8544EVTANG
Contents
Board
For Use With/related Products
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PPC8544EVTANG
Manufacturer:
FREESCALE
Quantity:
20 000
17.5
The RX eye diagram in
Figure
In general, the minimum receiver eye diagram measured with the compliance/test measurement load (see
Figure
input receiver of any real PCI Express component. The degraded eye diagram at the input receiver is due
to traces internal to the package as well as silicon parasitic characteristics which cause the real PCI Express
component to vary in impedance from the compliance/test measurement load. The input receiver eye
diagram is implementation specific and is not specified. RX component designer should provide additional
margin to adequately compensate for the degraded minimum receiver eye diagram (shown in
expected at the input receiver based on some adequate combination of system simulations and the return
loss measured looking into the RX package and silicon. The RX eye diagram must be aligned in time using
the jitter median to locate the center of the eye diagram.
Freescale Semiconductor
L
Notes:
1. No test load is necessarily associated with this value.
2. Specified at the measurement point and measured over any 250 consecutive UIs. The test load in
3. A T
4. The receiver input impedance shall result in a differential return loss greater than or equal to 15 dB with the D+ line biased to
5. Impedance during all LTSSM states. When transitioning from a fundamental reset to detect (the initial state of the LTSSM)
6. The RX DC common mode impedance that exists when no power is present or fundamental reset is asserted. This helps
7. It is recommended that the recovered TX UI is calculated using all edges in the 3500 consecutive UI interval with a fit algorithm
TX-SKEW
as the RX device when taking measurements (also refer to the receiver compliance eye diagram shown in
clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must
be used as a reference for the eye diagram.
interconnect collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to-MAX-JITTER specification ensures a jitter
distribution in which the median and the maximum deviation from the median is less than half of the total. UI jitter budget
collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median
describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged
time value. If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500
consecutive UI must be used as the reference for the eye diagram.
300 mV and the D– line biased to –300 mV and a common mode return loss greater than or equal to 6 dB (no bias required)
over a frequency range of 50 MHz to 1.25 GHz. This input impedance requirement applies to all valid input levels. The
reference impedance for return loss measurements for is 50 Ω to ground for both the D+ and D– line (that is, as measured
by a vector network analyzer with 50-Ω probes, see
loss measurement.
there is a 5-ms transition time before receiver termination values must be met on all unconfigured lanes of a port.
ensure that the receiver detect circuit will not falsely assume a receiver is powered on when it is not. This term must be
measured at 300 mV above the RX ground.
using a minimization merit function. Least squares and median deviation fits have worked well with experimental and
simulated data.
RX-EYE
Symbol
58) in place of any real PCI Express RX component.
58) will be larger than the minimum receiver eye diagram measured over a range of systems at the
Receiver Compliance Eye Diagrams
= 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the transmitter and
MPC8544E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
Table 60. Differential Receiver (RX) Input Specifications (continued)
Total skew
Parameter
Figure 57
is specified using the passive compliance/test measurement load (see
Min
—
Figure
Nom
—
58). Note that the series capacitors CTX is optional for the return
Max
20
Units
ns
Skew across all lanes on a link. This includes
variation in the length of SKP ordered set (for
example, COM and one to five symbols) at
the RX as well as any delay differences
arising from the interconnect itself.
Comments
Figure 58
Figure
should be used
Figure
PCI Express
57). If the
57)
79