S202SE2 Sharp Microelectronics, S202SE2 Datasheet

no-image

S202SE2

Manufacturer Part Number
S202SE2
Description
RELAY SSR 240VAC 8A ZC 4-SIP
Manufacturer
Sharp Microelectronics
Series
S202r
Datasheet

Specifications of S202SE2

Circuit
SPST-NO (1 Form A)
Output Type
AC, Zero Cross
Load Current
8A
Voltage - Input
1.2VDC
Voltage - Load
0 ~ 240 V
Mounting Type
Through Hole
Termination Style
PC Pin
Package / Case
4-SIP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
On-state Resistance
-
Other names
425-1251-5
■ Description
■ Features
S202SE2 Series
State Relays (SSR) are an integration of an infrared
emitting diode (IRED), a Phototriac Detector and a
main output Triac. These devices are ideally suited for
controlling high voltage AC loads with solid state
reliability while providing 3.0kV isolation (V
from input to output.
1. Output current, I
2. Zero crossing functionary (V
3. 4 pin SIP package
4. High repetitive peak off-state voltage (V
5. Reinforced insulation type (MIN. 0.4mm internal
6. High isolation voltage between input and output
7. Lead-free terminal components are also available
8. Screw hole for heat sink
Non-zero cross type is also available. (S202SE1 Series)
Notice The content of data sheet is subject to change without prior notice.
S202SE2 Series reinforced insulation type Solid
separation)
(V
(see Model Line-up section in this datasheet)
iso
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
(rms) : 3.0kV)
T
(rms)≤8.0A
OX
: MAX. 35V)
DRM
: 600V)
iso
(rms) )
1
■ Agency approvals/Compliance
■ Applications
I
Reinforced Insulation Type
Zero Cross type
SIP 4pin
Triac output SSR
1. Recognized by UL508, file No. E94758 (as models No.
2. Approved by CSA 22.2 No.14, file No. LR63705 (as
3. Approved by TÜV EN60950 (reinforced insulation),
4. Package resin : UL flammability grade (94V-0)
1. Isolated interface between high voltage AC devices
2. Switching motors, fans, heaters, solenoids, and
3. Power control in applications such as lighting and
T
(rms)≤8A,
S202SE2)
models No. S202SE2)
file No. R9051479 (as models No. S202SE2)
and lower voltage DC control circuitry.
valves.
temperature control equipment.
S202SE2 Series
Sheet No.:D4-A03301EN
© SHARP Corporation
Date Apr. 28. 2004

S202SE2 Summary of contents

Page 1

... Recognized by UL508, file No. E94758 (as models No. S202SE2) 2. Approved by CSA 22.2 No.14, file No. LR63705 (as models No. S202SE2) 3. Approved by TÜV EN60950 (reinforced insulation), (rms) ) file No. R9051479 (as models No. S202SE2) iso 4. Package resin : UL flammability grade (94V-0) ■ Applications 1. Isolated interface between high voltage AC devices and lower voltage DC control circuitry. ...

Page 2

... S202SE2 UL mark Model No. Date code (2 digit) 8A260VAC + − ±0.2 4-1.1 ±0.3 4-1.25 ±0.2 4-0 (5.08) (7.62) (2.54) Product mass : approx. 6. Typical dimensions Output (Triac T2) 1 Output (Triac T1) 2 Input (+) 3 Input (−) 4 (Unit : mm) ±0.2 5.5 ±0.1 0.6 (1.4) 2 S202SE2 Series Sheet No.: D4-A03301EN ...

Page 3

... Country of origin Japan Rank mark There is no rank mark indicator and currently there are no rank offered for this device. 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D 3 S202SE2 Series Sheet No.: D4-A03301EN ...

Page 4

... V (rms)=200V, AC60Hz (rms)=2A, Resistance load, I off T R (j-c) Between junction and case th R (j-a) Between junction and ambient th 4 S202SE2 Series Soldering area (T a MIN. TYP. MAX. − 1.2 1.4 − − 100 − − 100 =20mA − − ...

Page 5

... EN60950 (reinforced insulation) − Model No. − Please contact a local SHARP sales representative to see the actual status of the production. Case V DRM 200pcs/case [V] Approved S202SE2F 600 Case V DRM 200pcs/case [V] Approved S202SE2 600 5 S202SE2 Series I [mA =6V =30Ω) L MAX.8 I [mA =6V =30Ω) L MAX.8 Sheet No.: D4-A03301EN ...

Page 6

... Ambient Temperature 75 100 125 (˚C) a Fig.4 Forward Current vs. Forward Voltage 100 75 100 125 (˚C) c Fig.6 Maximum ON-state Power Dissipation vs. RMS ON-state Current f=60Hz T =25˚C Start j 100 6 S202SE2 Series − 100 Ambient temperature T (˚ =75˚C a 50˚C 25˚C 0˚C −25˚C ...

Page 7

... Remarks : Please be aware that all data in the graph are just for reference. Fig.8 Repetitive Peak OFF-state Current vs. Ambient Temperature =30Ω 100 125 (˚ S202SE2 Series −3 V =600V D −4 −5 −6 −7 −8 −9 − 100 Ambient temperature T (˚C) a Sheet No.: D4-A03301EN 125 ...

Page 8

... OUT Locate snubber circuit between output terminals I (rms) OUT (Cs=0.022µF, Rs=47Ω) f − T − opr ) must be 0.1mA or less increases faster than rated dV/dt, the Triac may turn on. To avoid this situation S202SE2 Series MIN. MAX. Unit 0 240 V I (rms) T 0.1 mA ∗ ...

Page 9

... Please keep 5mm distance as minimum between naked metal portion of SSR and heat sink, and also between naked metal portion of SSR and bis/nut/washer. However, please avoid the natural rubber for isolation sheet. 4.4mm MIN. : 3kV or more) iso Heat sink SSR : each 3kV or more) iso Isolation sheet Heat sink SSR 9 S202SE2 Series Sheet No.: D4-A03301EN ...

Page 10

... Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least twice the minimum required triggering current from initial operation. ● Standard Circuit Tr1 ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. S202SE2 Load 3 1 SSR Line Surge absorption circuit (Snubber circuit S202SE2 Series Sheet No.: D4-A03301EN ...

Page 11

... Please solder within one time. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. 11 S202SE2 Series Sheet No.: D4-A03301EN ...

Page 12

... This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. 12 S202SE2 Series Sheet No.: D4-A03301EN ...

Page 13

... The product should be located after the packing case is partitioned and protected inside by 4 pads. Each partition should have 5 products with the lead upward. Cushioning material and molt plane should be located after all products are settled (1 packing contains 200 pcs). Package composition Molt plane Cushioning material Product Partition 13 S202SE2 Series Pad Packing case Sheet No.: D4-A03301EN ...

Page 14

... SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this pub- lication. 14 S202SE2 Series Sheet No.: D4-A03301EN ...

Related keywords