05045C103MA79A AVX Corporation, 05045C103MA79A Datasheet - Page 28

• Manufacturer Part Number: 05045C103MA79A
• Description: CAP CER 10000PF 50V X7R 0504
• Manufacturer: AVX Corporation

Specifications of 05045C103MA79A

• Capacitance: 10000pF
• Voltage - Rated: 50V
• Tolerance: ±20%
• Temperature Coefficient: X7R
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: -55°C ~ 125°C
• Features: Low ESL
• Applications: General Purpose
• Package / Case: 0504 (1210 Metric)
• Size / Dimension: 0.050" L x 0.040" W (1.27mm x 1.02mm)
• Thickness: 1.02mm Max
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -
• Lead Spacing: -

RESISTANCE TO VIBRATION
Specification
Measuring Conditions
Specification
Measuring Conditions
General Specifications
Mechanical
SOLDERABILITY
26
END TERMINATION ADHERENCE
Specification
Measuring Conditions
No evidence of peeling of end terminal
After soldering devices to circuit board apply 5N
(0.51kg f) for 10 ± 1 seconds, please refer to Figure 1.
fresh solder
Dip device in eutectic solder at 230 ± 5°C for
2 ± .5 seconds
Deflection
TEST BOARD
Appearance:
No visual defects
Capacitance
Within specified tolerance
Q, Tan Delta
To meet initial requirement
Insulation Resistance
NP0, X7R
Z5U, Y5V
Vibration Frequency
10-2000 Hz
Maximum Acceleration
20G
Swing Width
1.5mm
Test Time
X, Y, Z axis for 2 hours each, total 6 hours of test
2mm
95% of each termination end should be covered with
5N FORCE
Figure 2. Bend Strength
Initial Value x 0.1
45mm
Initial Value x 0.3
DEVICE UNDER TEST
Speed = 1mm/sec
45mm
Terminal Adhesion
R340mm
Figure 1.
Supports
BEND STRENGTH
Specification
Measuring Conditions
RESISTANCE TO SOLDER HEAT
Specification
Measuring Conditions
Appearance:
No visual defects
Capacitance Variation
NP0: ± 5% or ± .5pF, whichever is larger
X7R: ≤ ± 12%
Z5U: ≤ ± 30%
Y5V: ≤ ± 30%
Insulation Resistance
NP0: ≥ Initial Value x 0.3
X7R: ≥ Initial Value x 0.3
Z5U: ≥ Initial Value x 0.1
Y5V: ≥ Initial Value x 0.1
Please refer to Figure 2
Deflection:
2mm
Test Time:
30 seconds
Appearance:
No serious defects, <25% leaching of either end
terminal
Capacitance Variation
NP0: ± 2.5% or ± 2.5pF, whichever is greater
X7R: ≤ ± 7.5%
Z5U: ≤ ± 20%
Y5V: ≤ ± 20%
Q, Tan Delta
To meet initial requirement
Insulation Resistance
To meet initial requirement
Dielectric Strength
No problem observed
Dip device in eutectic solder at 260°C, for 1 minute.
Store at room temperature for 48 hours (24 hours for
NP0) before measuring electrical parameters.
Part sizes larger than 3.20mm x 2.49mm are
preheated at 150°C for 30 ±5 seconds before
performing test.