PIC12CE673-04/P Microchip Technology, PIC12CE673-04/P Datasheet - Page 290

• Manufacturer Part Number: PIC12CE673-04/P
• Description: IC MCU OTP 1KX14 A/D&EE 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12CE673-04/P

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: OTP
• Eeprom Size: 16 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 16Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Processor Series: PIC12C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 8
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
17.3.5
17.3.6
DS31017A-page 17-14
Slave Mode
Slave Select Synchronization
In slave mode, the data is transmitted and received as the external clock pulses appear on SCK.
When the last bit is latched, the SSPIF interrupt flag bit is set.
While in slave mode the external clock is supplied by the external clock source on the SCK pin.
This external clock must meet the minimum high and low times as specified in the electrical spec-
ifications.
While in sleep mode, the slave can transmit/receive data. When a byte is receive the device will
wake-up from sleep.
The SS pin allows a synchronous slave mode. The SPI must be in slave mode with SS pin
control enabled (SSPCON1<3:0> = 04h). The pin must not be driven low for the SS pin to
function as an input. The Data Latch must be high. When the SS pin is low, transmission
and reception are enabled and the SDO pin is driven. When the SS pin goes high, the SDO
pin is no longer driven, even if in the middle of a transmitted byte, and becomes a floating
output. External pull-up/ pull-down resistors may be desirable, depending on the application.
When the SPI module resets, the bit counter is forced to 0. This can be done by either by forcing
the SS pin to a high level or clearing the SSPEN bit.
To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the
SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables
transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot
create a bus conflict.
Note 1: When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> =
Note 2: If the SPI is used in Slave Mode with CKE is set, then the SS pin control must be
0100) the SPI module will reset if the SS pin is set to V
enabled.
Preliminary
1997 Microchip Technology Inc.
DD
.