DSPIC30F3014-20I/ML Microchip Technology, DSPIC30F3014-20I/ML Datasheet - Page 61

• Manufacturer Part Number: DSPIC30F3014-20I/ML
• Description: IC DSPIC MCU/DSP 24K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F3014-20I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 24KB (8K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 30
• Flash Memory Size: 24KB
• Supply Voltage Range: 2.5V To 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F301420IML

TABLE 8-2:
 2010 Microchip Technology Inc.
Interrupt
Number
28-40
43-53
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
41
42
11
0
1
2
3
4
5
6
7
8
9
Number
Highest Natural Order Priority
Vector
Lowest Natural Order Priority
36-48
51-61
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
49
50
8
9
dsPIC30F4013 INTERRUPT
VECTOR TABLE
INT0 – External Interrupt 0
IC1 – Input Capture 1
OC1 – Output Compare 1
T1 – Timer1
IC2 – Input Capture 2
OC2 – Output Compare 2
T2 V Timer2
T3 – Timer3
SPI1
U1RX – UART1 Receiver
U1TX – UART1 Transmitter
ADC – ADC Convert Done
NVM – NVM Write Complete
SI2C – I
MI2C – I
Input Change Interrupt
INT1 – External Interrupt 1
IC7 – Input Capture 7
IC8 – Input Capture 8
OC3 – Output Compare 3
OC4 – Output Compare 4
T4 – Timer4
T5 – Timer5
INT2 – External Interrupt 2
U2RX – UART2 Receiver
U2TX – UART2 Transmitter
Reserved
C1 – Combined IRQ for CAN1
Reserved
DCI – CODEC Transfer Done
LVD – Low-Voltage Detect
Reserved
Interrupt Source
2
2
C™ Slave Interrupt
C Master Interrupt
8.2
A Reset is not a true exception because the interrupt
controller is not involved in the Reset process. The pro-
cessor initializes its registers in response to a Reset
which forces the PC to zero. The processor then begins
program execution at location 0x000000. A GOTO
instruction is stored in the first program memory loca-
tion immediately followed by the address target for the
GOTO instruction. The processor executes the GOTO to
the specified address and then begins operation at the
specified target (start) address.
8.2.1
In addition to external Reset and Power-on Reset
(POR), these sources of error conditions ‘trap’ to the
Reset vector:
• Watchdog Time-out:
• Uninitialized W Register Trap:
• Illegal Instruction Trap:
• Brown-out Reset (BOR):
• Trap Lockout:
The watchdog has timed out, indicating that the
processor is no longer executing the correct flow
of code.
An attempt to use an uninitialized W register as
an Address Pointer causes a Reset.
Attempted execution of any unused opcodes
results in an illegal instruction trap. Note that a
fetch of an illegal instruction does not result in an
illegal instruction trap if that instruction is flushed
prior to execution due to a flow change.
A momentary dip in the power supply to the
device has been detected which may result in
malfunction.
Occurrence of multiple trap conditions
simultaneously causes a Reset.
dsPIC30F3014/4013
Reset Sequence
RESET SOURCES
DS70138G-page 61