MC56F8145VFGE Freescale Semiconductor, MC56F8145VFGE Datasheet - Page 26

• Manufacturer Part Number: MC56F8145VFGE
• Description: IC DSP 16BIT 40MHZ 128-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8145VFGE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 128-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F81xx
• Core: 56800E
• Data Ram Size: 4 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 49
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4 x 12 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

26
PHASEA0
PHASEB0
(GPIOC4)
(GPIOC5)
Signal
Name
TRST
(TA0)
(TA1)
Table 2-2 Signal and Package Information for the 128-Pin LQFP
Pin No.
114
127
128
Schmitt
Schmitt
Schmitt
Schmitt
Schmitt
Schmitt
Schmitt
Output
Output
Output
Output
Input/
Input/
Input/
Input/
Type
Input
Input
Input
pulled high
56F8345 Technical Data, Rev. 17
internally
enabled
enabled
During
pull-up
pull-up
Reset
Input,
Input,
Input,
State
Test Reset — As an input, a low signal on this pin provides a
reset signal to the JTAG TAP controller. To ensure complete
hardware reset, TRST should be asserted whenever RESET is
asserted. The only exception occurs in a debugging environment
when a hardware device reset is required and the JTAG/EOnCE
module must not be reset. In this case, assert RESET, but do not
assert TRST.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Note:
design is to be used in a debugging environment, TRST may be tied to
V
Phase A — Quadrature Decoder 0, PHASEA input
TA0 — Timer A, Channel 0
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is PHASEA0.
To deactivate the internal pull-up resistor, clear bit 4 of the
GPIOC_PUR register.
Phase B — Quadrature Decoder 0, PHASEB input
TA1 — Timer A, Channel 1
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is PHASEB0.
To deactivate the internal pull-up resistor, clear bit 5 of the
GPIOC_PUR register.
SS
through a 1K resistor.
For normal operation, connect TRST directly to V
Signal Description
Freescale Semiconductor
SS
Preliminary
. If the