MC908QB8CDWER Freescale Semiconductor, MC908QB8CDWER Datasheet - Page 158

• Manufacturer Part Number: MC908QB8CDWER
• Description: IC MCU 8BIT 8K FLASH 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QB8CDWER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• For Use With: DEMO908QB8 - BOARD DEMO FOR MC68HC908QB8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: MC908QB8CDWERTR

Serial Peripheral Interface (SPI) Module
15.3.1 Master Mode
The SPI operates in master mode when the SPI master bit, SPMSTR, is set.
Only a master SPI module can initiate transmissions. Software begins the transmission from a master SPI
module by writing to the transmit data register. If the shift register is empty, the byte immediately transfers
to the shift register, setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the MOSI
pin under the control of the serial clock. See
The SPR1 and SPR0 bits control the baud rate generator and determine the speed of the shift register.
(See
master also controls the shift register of the slave peripheral.
While the byte shifts out on the MOSI pin of the master, another byte shifts in from the slave on the
master’s MISO pin. The transmission ends when the receiver full bit, SPRF, becomes set. At the same
time that SPRF becomes set, the byte from the slave transfers to the receive data register. In normal
operation, SPRF signals the end of a transmission. Software clears SPRF by reading the SPI status and
control register (SPSCR) with SPRF set and then reading the SPI data register (SPDR). Writing to SPDR
clears SPTE.
15.3.2 Slave Mode
The SPI operates in slave mode when SPMSTR is clear. In slave mode, the SPSCK pin is the input for
the serial clock from the master MCU. Before a data transmission occurs, the SS pin of the slave SPI must
be low. SS must remain low until the transmission is complete. See
In a slave SPI module, data enters the shift register under the control of the serial clock from the master
SPI module. After a byte enters the shift register of a slave SPI, it transfers to the receive data register,
and the SPRF bit is set. To prevent an overflow condition, slave software then must read the receive data
register before another full byte enters the shift register.
The maximum frequency of the SPSCK for an SPI configured as a slave is the bus clock speed (which is
twice as fast as the fastest master SPSCK clock that can be generated). The frequency of the SPSCK for
an SPI configured as a slave does not have to correspond to any SPI baud rate. The baud rate only
158
15.8.2 SPI Status and Control
In a multi-SPI system, configure the SPI modules as master or slave before
enabling them. Enable the master SPI before enabling the slave SPI.
Disable the slave SPI before disabling the master SPI. See
Control
SHIFT REGISTER
GENERATOR
MASTER MCU
BAUD RATE
Register.
Figure 15-3. Full-Duplex Master-Slave Connections
Register.) Through the SPSCK pin, the baud rate generator of the
MC68HC908QB8 Data Sheet, Rev. 3
MISO
MOSI
SPSCK
SS
Figure
NOTE
V
15-3.
DD
SPSCK
MISO
MOSI
SS
15.3.6.2 Mode Fault
SHIFT REGISTER
15.8.1 SPI
SLAVE MCU
Freescale Semiconductor
Error.