MC9S08QG4CPAE Freescale Semiconductor, MC9S08QG4CPAE Datasheet - Page 90

• Manufacturer Part Number: MC9S08QG4CPAE
• Description: IC MCU 4K FLASH 8MHZ 8-DIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG4CPAE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 4
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 7 Central Processor Unit (S08CPUV2)
7.2
Figure 7-1
7.2.1
The A accumulator is a general-purpose 8-bit register. One operand input to the arithmetic logic unit
(ALU) is connected to the accumulator and the ALU results are often stored into the A accumulator after
arithmetic and logical operations. The accumulator can be loaded from memory using various addressing
modes to specify the address where the loaded data comes from, or the contents of A can be stored to
memory using various addressing modes to specify the address where data from A will be stored.
Reset has no effect on the contents of the A accumulator.
7.2.2
This 16-bit register is actually two separate 8-bit registers (H and X), which often work together as a 16-bit
address pointer where H holds the upper byte of an address and X holds the lower byte of the address. All
indexed addressing mode instructions use the full 16-bit value in H:X as an index reference pointer;
however, for compatibility with the earlier M68HC05 Family, some instructions operate only on the
low-order 8-bit half (X).
Many instructions treat X as a second general-purpose 8-bit register that can be used to hold 8-bit data
values. X can be cleared, incremented, decremented, complemented, negated, shifted, or rotated. Transfer
instructions allow data to be transferred from A or transferred to A where arithmetic and logical operations
can then be performed.
For compatibility with the earlier M68HC05 Family, H is forced to 0x00 during reset. Reset has no effect
on the contents of X.
88
Programmer’s Model and CPU Registers
shows the five CPU registers. CPU registers are not part of the memory map.
Accumulator (A)
Index Register (H:X)
H
CONDITION CODE REGISTER
15
15
INDEX REGISTER (HIGH)
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
16-BIT INDEX REGISTER H:X
PROGRAM COUNTER
STACK POINTER
Figure 7-1. CPU Registers
8
V 1 1 H I N Z
7
7
7
INDEX REGISTER (LOW)
ACCUMULATOR
C
0
0
0
0
CARRY
ZERO
NEGATIVE
INTERRUPT MASK
HALF-CARRY (FROM BIT 3)
TWO’S COMPLEMENT OVERFLOW
SP
PC
CCR
A
X
Freescale Semiconductor