PIC18F25J11-I/SS Microchip Technology, PIC18F25J11-I/SS Datasheet - Page 243

• Manufacturer Part Number: PIC18F25J11-I/SS
• Description: IC PIC MCU FLASH 32K 2V 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F25J11-I/SS

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Interface: EUSART, I2C, SPI
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183022, DM183032, DV164136, MA180023
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

In addition to the expanded range of modes available
through the CCPxCON and ECCPxAS registers, the
ECCP modules have two additional registers associated
with Enhanced PWM operation and auto-shutdown
features. They are:
• ECCPxDEL (Enhanced PWM Control)
• PSTRxCON (Pulse Steering Control)
17.1
The Enhanced CCP module may have up to four PWM
outputs, depending on the selected operating mode.
These outputs, designated PxA through PxD, are
routed through the Peripheral Pin Select (PPS)
module. Therefore, individual functions may be
mapped to any of the remappable I/O pins, RPn. The
outputs that are active depend on the ECCP operating
mode selected. The pin assignments are summarized
in Table 17-4.
To configure the I/O pins as PWM outputs, the proper
PWM mode must be selected by setting the PxM<1:0>
and CCPxM<3:0> bits. The appropriate TRIS direction
bits for the port pins must also be set as outputs and the
output functions need to be assigned to I/O pins in the
PPS module. (For details on configuring the module,
see Section 9.7 “Peripheral Pin Select (PPS)”.)
17.1.1
The ECCP modules utilize Timers 1, 2, 3 or 4, depending
on the mode selected. Timer1 and Timer3 are available
to modules in Capture or Compare modes, while Timer2
and Timer4 are available for modules in PWM mode.
TABLE 17-1:
The assignment of a particular timer to a module is
determined by the Timer-to-ECCP enable bits in the
TCLKCON register (Register 12-3). The interactions
between the two modules are depicted in Figure 17-1.
Capture operations are designed to be used when the
timer is configured for Synchronous Counter mode.
Capture operations may not work as expected if the
associated timer is configured for Asynchronous Counter
mode.
© 2009 Microchip Technology Inc.
ECCP Mode
Compare
Capture
ECCP Outputs and Configuration
PWM
ECCP MODULE AND TIMER
RESOURCES
ECCP MODE – TIMER
RESOURCE
Timer1 or Timer3
Timer1 or Timer3
Timer2 or Timer4
Timer Resource
PIC18F46J11 FAMILY
17.2
In Capture mode, the CCPRxH:CCPRxL register pair
captures the 16-bit value of the TMR1 or TMR3
registers when an event occurs on the corresponding
ECCPx pin. An event is defined as one of the following:
• Every falling edge
• Every rising edge
• Every 4
• Every 16
The event is selected by the mode select bits,
CCPxM<3:0>, of the CCPxCON register. When a
capture is made, the interrupt request flag bit, CCPxIF,
is set; it must be cleared by software. If another capture
occurs before the value in register CCPRx is read, the
old captured value is overwritten by the new captured
value.
17.2.1
In Capture mode, the appropriate ECCPx pin should be
configured as an input by setting the corresponding
TRIS direction bit.
Additionally, the ECCPx input function needs to be
assigned to an I/O pin through the Peripheral Pin
Select module. For details on setting up the
remappable pins, see Section 9.7 “Peripheral Pin
Select (PPS)”.
17.2.2
The timers that are to be used with the capture feature
(Timer1 and/or Timer3) must be running in Timer mode
or Synchronized Counter mode. In Asynchronous
Counter mode, the capture operation may not work.
The timer to be used with each ECCP module is
selected in the TCLKCON register (Register 12-3).
17.2.3
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep the
CCPxIE interrupt enable bit clear to avoid false interrupts.
The interrupt flag bit, CCPxIF, should also be cleared
following any such change in operating mode.
Note:
Capture Mode
th
th
ECCP PIN CONFIGURATION
If the ECCPx pin is configured as an out-
put, a write to the port can cause a capture
condition.
TIMER1/TIMER3 MODE SELECTION
SOFTWARE INTERRUPT
rising edge
rising edge
DS39932C-page 243