PIC18F2480-I/SO Microchip Technology, PIC18F2480-I/SO Datasheet - Page 215

• Manufacturer Part Number: PIC18F2480-I/SO
• Description: IC PIC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2480-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163011, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.4.7
In I
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 17-17). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to 0 and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (T
Q2 and Q4 clocks. In I
reloaded automatically.
FIGURE 17-17:
TABLE 17-3:
© 2007 Microchip Technology Inc.
Note 1:
2
C Master mode, the Baud Rate Generator (BRG)
10 MHz
10 MHz
10 MHz
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
F
CY
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE W/BRG
BAUD RATE GENERATOR BLOCK DIAGRAM
SSPM3:SSPM0
2
C Master mode, the BRG is
SCL
SSPM3:SSPM0
20 MHz
20 MHz
20 MHz
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
F
CY
CY
PIC18F2480/2580/4480/4580
*2
) on the
Reload
Control
Preliminary
CLKO
Reload
Once the given operation is complete (i.e., transmis-
sion of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
Table 17-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
2
BRG Down Counter
C specification (which applies to rates greater than
SSPADD<6:0>
BRG Value
0Dh
0Ah
0Ah
19h
20h
64h
28h
03h
00h
F
OSC
(2 Rollovers of BRG)
/4
400 kHz
400 kHz
333 kHz
312.5 kHz
1 MHz
DS39637C-page 213
100 kHz
308 kHz
100 kHz
100 kHz
F
SCL
(1)
(1)
(1)
(1)