MC9S08JM16CLC Freescale Semiconductor, MC9S08JM16CLC Datasheet - Page 295

• Manufacturer Part Number: MC9S08JM16CLC
• Description: MCU 8BIT 16K FLASH 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM16CLC

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 4 Channel
• Controller Family/series: HCS08
• No. Of I/o's: 21
• Ram Memory Size: 1KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Package: 32LQFP
• Family Name: HCS08
• Maximum Speed: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 17
Universal Serial Bus Device Controller (S08USBV1)
17.1
This chapter describes an universal serial bus device controller (S08USBV1) module that is based on the
Universal Serial Bus Specification Rev 2.0. The USB bus is designed to replace existing bus interfaces
such as RS-232, PS/2, and IEEE 1284 for PC peripherals.
The S08USBV1 module provides a single-chip solution for full-speed (12 Mbps) USB device applica-
tions, and integrates the required transceiver with Serial Interface Engine (SIE), 3.3 V regulator, Endpoint
RAM and other control logics.
17.1.1
The S08USBV1 requires two clock sources, the 24 MHz bus clock and a 48 MHz reference clock. The
48 MHz clock is sourced directly from MCGOUT. To achieve the 48 MHz clock rate, the MCG must be
configured properly for PLL engaged external (PEE) mode with an external crystal.
For USB operation, examples of MCG configuration using PEE mode include:
17.1.2
In USB suspend mode, the S08USBV1 current consumption is limited to 500 μA. When the USB device
goes into suspend mode, the firmware typically enters stop3 to meet the USB suspend requirements on
current consumption.
17.1.3
If using an external 3.3 V regulator as an input to V
V
(USBVREN = 1), do not connect an external supply to the V
3.9 V and 5.5 V for the internal 3.3 V regulator to operate correctly.
Freescale Semiconductor
DD
•
•
, must not fall below the input voltage at the V
2 MHz crystal – RDIV = 000 and VDIV = 0110
4 MHz crystal – RDIV = 001 and VDIV = 0110
Introduction
Clocking Requirements
Current Consumption in USB Suspend
3.3 V Regulator
Enabling LVD increases current consumption in stop3. Consequently, when
trying to satisfy USB suspend requirements, disabling LVD before entering
stop3.
MC9S08JM16 Series Data Sheet, Rev. 2
NOTE
USB33
USB33
(only when USBVREN = 0), the supply voltage,
pin. If using the internal 3.3 V regulator
USB33
pin. In this case, V
DD
must fall between
295