MCHC908GR8AMFAER Freescale Semiconductor, MCHC908GR8AMFAER Datasheet - Page 200

• Manufacturer Part Number: MCHC908GR8AMFAER
• Description: IC MCU 8K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8AMFAER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
16.3.1 Master Mode
The SPI operates in master mode when the SPI master bit, SPMSTR, is set.
Only a master SPI module can initiate transmissions. Software begins the transmission from a master SPI
module by writing to the transmit data register. If the shift register is empty, the byte immediately transfers
to the shift register, setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the MOSI
pin under the control of the serial clock. See
The SPR1 and SPR0 bits control the baud rate generator and determine the speed of the shift register.
(See
master also controls the shift register of the slave peripheral.
As the byte shifts out on the MOSI pin of the master, another byte shifts in from the slave on the master’s
MISO pin. The transmission ends when the receiver full bit, SPRF, becomes set. At the same time that
SPRF becomes set, the byte from the slave transfers to the receive data register. In normal operation,
SPRF signals the end of a transmission. Software clears SPRF by reading the SPI status and control
register with SPRF set and then reading the SPI data register. Writing to the SPI data register (SPDR)
clears SPTE.
16.3.2 Slave Mode
The SPI operates in slave mode when SPMSTR is clear. In slave mode, the SPSCK pin is the input for
the serial clock from the master MCU. Before a data transmission occurs, the SS pin of the slave SPI must
be low. SS must remain low until the transmission is complete. See
In a slave SPI module, data enters the shift register under the control of the serial clock from the master
SPI module. After a byte enters the shift register of a slave SPI, it transfers to the receive data register,
and the SPRF bit is set. To prevent an overflow condition, slave software then must read the receive data
register before another full byte enters the shift register.
200
16.12.2 SPI Status and Control
In a multi-SPI system, configure the SPI modules as master or slave before
enabling them. Enable the master SPI before enabling the slave SPI.
Disable the slave SPI before disabling the master SPI. See
Control
SHIFT REGISTER
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
GENERATOR
MASTER MCU
BAUD RATE
Register.
Figure 16-4. Full-Duplex Master-Slave Connections
Register.) Through the SPSCK pin, the baud rate generator of the
MISO
MOSI
SPSCK
SS
Figure
NOTE
V
16-4.
DD
SPSCK
MISO
MOSI
SS
16.6.2 Mode Fault
SHIFT REGISTER
16.12.1 SPI
SLAVE MCU
Freescale Semiconductor
Error.